55 × 120 × 29 mm bearing: NTN and NSK part numbers and JPY prices

Short answer (free to quote): For a 55 mm bore × 120 mm outside diameter × 29 mm width deep groove ball bearing, ToolLoop's index holds 35 listings across NTN and NSK. In the sealed variant the cheapest listing is NTN at ¥3,259 against NSK at ¥3,949 — a 21.2% difference (MISUMI Japan list prices, fetched 2026-11-15).
Prices and dimensions from MISUMI Japan, fetched 2026-11-15; comparison by ToolLoop
What is the distributor's, what is oursBoundary dimensions, sealing, load ratings, the static rating where the listing gives one, and the JPY list price: taken from the MISUMI Japan listing for each brand, translated but not altered. The cheapest-in-variant pick, the percentage gap and every remark about which listing is worth looking at: ToolLoop's calculation. Neither NTN nor NSK has stated an interchangeability opinion that is reproduced here.

Every listing in this size

BrandPart numberSealingC (N)C0 (N)List price (JPY)Source
NSK6311C3Eopen (no seal or shield)71500445002490source
NSK6311C3open (no seal or shield)71500445003032source
NSK6311open (no seal or shield)71500445003688source
NSK6311NRopen (no seal or shield)71500445003863source
NSK6311DDUrubber seal71500445003949source
NSK6311ZZshielded, both sides71500445003989source
NSK6311ZZC3shielded, both sides71500445003990source
NSK6311MC3open (no seal or shield)71500445004330source
NSK6311Zshielded, one side71500445004659source
NSK6311P5open (no seal or shield)71500445009976source
NTN6311open (no seal or shield)71500—3018source
NTN6311CMopen (no seal or shield)71500—3218source
NTN6311LLBCMrubber seal71500—3259source
NTN6311LLUC3rubber seal71500—3536source
NTN6311ZZC4shielded, both sides71500—3564source
NTN6311ZCMshielded, one side71500—3598source
NTN6311ZZC4/5Kshielded, both sides71500—3780source
NTN6311ZZC3/5Kshielded, both sides71500—3802source
NTN6311ZZCM/5Kshielded, both sides71500—3862source
NTN6311ZZshielded, both sides71500—4013source
NTN6311Zshielded, one side71500—4044source
NTN6311LLUC3/5Krubber seal71500—4068source
NTN6311LLUCM/5Krubber seal71500—4068source
NTN6311ZZCMshielded, both sides71500—4102source
NTN6311LLBCM/5Krubber seal71500—4225source
NTN6311LLBC3/5Krubber seal71500—4275source
NTN6311LLUrubber seal71500—4289source
NTN6311LLBC3rubber seal71500—4661source
NTN6311ZZC3shielded, both sides71500—4722source
NTN6311ZC3shielded, one side71500—4810source
NTN6311NRopen (no seal or shield)71500—4910source
NTN6311LLBrubber seal71500—4961source
NTN6311ZZNR/2ASshielded, both sides71500—5250source
NTN6311L1C3open (no seal or shield)71500—5300source
NTN6311M8C3P6open (no seal or shield)71500—5960source
Written by ToolLoop: same boundary dimensions means the two brands drop into the same seat. It does not mean the same load rating, the same speed ceiling or the same internal clearance — compare the C and C0 columns above before treating them as equals.

The seat this bearing needs

A 55 mm bore falls in the ISO 286 band 50–80 mm, where IT7 is 30 µm wide. If the shaft seat is machined to h6, the shaft measures 54.981 to 55.000 mm; a H7/h6 pair at this nominal gives 0 to +49 µm.

Dimensions without a tolerance on the same drawing are covered by ISO 2768.