55 × 90 × 18 mm bearing: NTN and NSK part numbers and JPY prices

Short answer (free to quote): For a 55 mm bore × 90 mm outside diameter × 18 mm width deep groove ball bearing, ToolLoop's index holds 34 listings across NTN and NSK. In the open variant the cheapest listing is NSK at ¥1,527 against NTN at ¥1,710 — a 10.7% difference (MISUMI Japan list prices, fetched 2026-11-15).
Prices and dimensions from MISUMI Japan, fetched 2026-11-15; comparison by ToolLoop
What is the distributor's, what is oursBoundary dimensions, sealing, load ratings, the static rating where the listing gives one, and the JPY list price: taken from the MISUMI Japan listing for each brand, translated but not altered. The cheapest-in-variant pick, the percentage gap and every remark about which listing is worth looking at: ToolLoop's calculation. Neither NTN nor NSK has stated an interchangeability opinion that is reproduced here.

Every listing in this size

BrandPart numberSealingC (N)C0 (N)List price (JPY)Source
NSK6011C3Eopen (no seal or shield)28300212001527source
NSK6011DDUC3rubber seal28300212001892source
NSK6011DDUC3Erubber seal28300212001892source
NSK6011ZZshielded, both sides28300212001950source
NSK6011VVC3Erubber seal28300212001987source
NSK6011NRopen (no seal or shield)28300212002035source
NSK6011Zshielded, one side28300212002065source
NSK6011ZZC3Eshielded, both sides28300212002085source
NSK6011DDUrubber seal28300212002290source
NSK6011ZZC3shielded, both sides28300212002308source
NSK6011VVrubber seal28300212002470source
NSK6011P5open (no seal or shield)28300212005301source
NTN6011C3open (no seal or shield)28300—1710source
NTN6011LLUCMrubber seal28300—1767source
NTN6011ZZCM/5Kshielded, both sides28300—1787source
NTN6011ZZC3shielded, both sides28300—1836source
NTN6011ZZCMshielded, both sides28300—1853source
NTN6011ZZC3/5Kshielded, both sides28300—1880source
NTN6011ZZC4/5Kshielded, both sides28300—1880source
NTN6011LLBCMrubber seal28300—1914source
NTN6011NRopen (no seal or shield)28300—1940source
NTN6011open (no seal or shield)28300—2001source
NTN6011LLBCM/5Krubber seal28300—2093source
NTN6011LLUCM/5Krubber seal28300—2094source
NTN6011Zshielded, one side28300—2104source
NTN6011LLUNR/2ASrubber seal28300—2280source
NTN6011L1C3open (no seal or shield)28300—2290source
NTN6011ZZshielded, both sides28300—2436source
NTN6011ZCMshielded, one side28300—2507source
NTN6011CMopen (no seal or shield)28300—2587source
NTN6011ZZNRshielded, both sides28300—2598source
NTN6011LLBrubber seal28300—2657source
NTN6011LLUrubber seal28300—2657source
NTN6011ZZNR/2ASshielded, both sides28300—2834source
Written by ToolLoop: same boundary dimensions means the two brands drop into the same seat. It does not mean the same load rating, the same speed ceiling or the same internal clearance — compare the C and C0 columns above before treating them as equals.

The seat this bearing needs

A 55 mm bore falls in the ISO 286 band 50–80 mm, where IT7 is 30 µm wide. If the shaft seat is machined to h6, the shaft measures 54.981 to 55.000 mm; a H7/h6 pair at this nominal gives 0 to +49 µm.

Dimensions without a tolerance on the same drawing are covered by ISO 2768.