60 × 95 × 18 mm bearing: NTN and NSK part numbers and JPY prices

Short answer (free to quote): For a 60 mm bore × 95 mm outside diameter × 18 mm width deep groove ball bearing, ToolLoop's index holds 39 listings across NTN and NSK. In the sealed variant the cheapest listing is NTN at ¥1,912 against NSK at ¥2,441 — a 27.7% difference (MISUMI Japan list prices, fetched 2026-11-15).
Prices and dimensions from MISUMI Japan, fetched 2026-11-15; comparison by ToolLoop
What is the distributor's, what is oursBoundary dimensions, sealing, load ratings, the static rating where the listing gives one, and the JPY list price: taken from the MISUMI Japan listing for each brand, translated but not altered. The cheapest-in-variant pick, the percentage gap and every remark about which listing is worth looking at: ToolLoop's calculation. Neither NTN nor NSK has stated an interchangeability opinion that is reproduced here.

Every listing in this size

BrandPart numberSealingC (N)C0 (N)List price (JPY)Source
NSK6012C3Eopen (no seal or shield)29500232001689source
NSK6012ZZC3Eshielded, both sides29500232002049source
NSK6012NRopen (no seal or shield)29500232002113source
NSK6012open (no seal or shield)29500232002178source
NSK6012VVrubber seal29500232002441source
NSK6012ZZNRshielded, both sides29500232002443source
NSK6012Zshielded, one side29500232002497source
NSK6012DDUrubber seal29500232002683source
NSK6012P5open (no seal or shield)29500232005829source
NSK6012-H-20DDUrubber seal295002320017699source
NTN6012C3open (no seal or shield)29500—1817source
NTN6012CMopen (no seal or shield)29500—1817source
NTN6012ZZCMshielded, both sides29500—1828source
NTN6012C4open (no seal or shield)29500—1860source
NTN6012LLBCMrubber seal29500—1912source
NTN6012ZC3shielded, one side29500—2050source
NTN6012NRopen (no seal or shield)29500—2120source
NTN6012open (no seal or shield)29500—2235source
NTN6012LUrubber seal29500—2250source
NTN6012ZZC3shielded, both sides29500—2307source
NTN6012ZZshielded, both sides29500—2346source
NTN6012LBrubber seal29500—2359source
NTN6012LLUCMrubber seal29500—2366source
NTN6012ZZNR/2ASshielded, both sides29500—2401source
NTN6012ZZNRshielded, both sides29500—2403source
NTN6012LLUCM/5Krubber seal29500—2491source
NTN6012ZZCM/5Kshielded, both sides29500—2511source
NTN6012LLUrubber seal29500—2531source
NTN6012LLBCM/5Krubber seal29500—2534source
NTN6012Zshielded, one side29500—2600source
NTN6012ZCMshielded, one side29500—2616source
NTN6012LLUNR/2ASrubber seal29500—2626source
NTN6012LLBNR/2ASrubber seal29500—2723source
NTN6012LLBNRrubber seal29500—2879source
NTN6012LLBrubber seal29500—3068source
NTN6012ZZC3/5Kshielded, both sides29500—3187source
NTN6012LLUNRrubber seal29500—3599source
NTN6012P5open (no seal or shield)29500—7402source
NTN6012P4open (no seal or shield)29500—8730source
Written by ToolLoop: same boundary dimensions means the two brands drop into the same seat. It does not mean the same load rating, the same speed ceiling or the same internal clearance — compare the C and C0 columns above before treating them as equals.

The seat this bearing needs

A 60 mm bore falls in the ISO 286 band 50–80 mm, where IT7 is 30 µm wide. If the shaft seat is machined to h6, the shaft measures 59.981 to 60.000 mm; a H7/h6 pair at this nominal gives 0 to +49 µm.

Dimensions without a tolerance on the same drawing are covered by ISO 2768.