65 × 100 × 18 mm bearing: NTN and NSK part numbers and JPY prices

Short answer (free to quote): For a 65 mm bore × 100 mm outside diameter × 18 mm width deep groove ball bearing, ToolLoop's index holds 31 listings across NTN and NSK. In the open variant the cheapest listing is NSK at ¥1,895 against NTN at ¥2,308 — a 17.9% difference (MISUMI Japan list prices, fetched 2026-11-15).
Prices and dimensions from MISUMI Japan, fetched 2026-11-15; comparison by ToolLoop
What is the distributor's, what is oursBoundary dimensions, sealing, load ratings, the static rating where the listing gives one, and the JPY list price: taken from the MISUMI Japan listing for each brand, translated but not altered. The cheapest-in-variant pick, the percentage gap and every remark about which listing is worth looking at: ToolLoop's calculation. Neither NTN nor NSK has stated an interchangeability opinion that is reproduced here.

Every listing in this size

BrandPart numberSealingC (N)C0 (N)List price (JPY)Source
NSK6013C3Eopen (no seal or shield)30500252001895source
NSK6013VVC3rubber seal30500252002478source
NSK6013DDUC3Erubber seal30500252002544source
NSK6013DUCMrubber seal30500252002544source
NSK6013NRopen (no seal or shield)30500252002547source
NSK6013open (no seal or shield)30500252002602source
NSK6013ZZshielded, both sides30500252002625source
NSK6013ZZNRshielded, both sides30500252002626source
NSK6013MC3open (no seal or shield)30500252002901source
NSK6013DDUrubber seal30500252003263source
NSK6013P5open (no seal or shield)30500252007010source
NTN6013CMopen (no seal or shield)30500—2308source
NTN6013ZZC3/5Kshielded, both sides30500—2360source
NTN6013LLBCMrubber seal30500—2417source
NTN6013ZC3shielded, one side30500—2512source
NTN6013LLBCM/5Krubber seal30500—2567source
NTN6013LBrubber seal30500—2570source
NTN6013ZZCM/5Kshielded, both sides30500—2586source
NTN6013LLUC3/5Krubber seal30500—2590source
NTN6013LUrubber seal30500—2590source
NTN6013ZZCMshielded, both sides30500—2610source
NTN6013NRopen (no seal or shield)30500—2624source
NTN6013LLUCMrubber seal30500—2737source
NTN6013LLUCM/5Krubber seal30500—2779source
NTN6013ZZshielded, both sides30500—2933source
NTN6013Zshielded, one side30500—3045source
NTN6013ZCMshielded, one side30500—3049source
NTN6013LLBrubber seal30500—3078source
NTN6013open (no seal or shield)30500—3139source
NTN6013LLUrubber seal30500—3213source
NTN6013P5open (no seal or shield)30500—9708source
Written by ToolLoop: same boundary dimensions means the two brands drop into the same seat. It does not mean the same load rating, the same speed ceiling or the same internal clearance — compare the C and C0 columns above before treating them as equals.

The seat this bearing needs

A 65 mm bore falls in the ISO 286 band 50–80 mm, where IT7 is 30 µm wide. If the shaft seat is machined to h6, the shaft measures 64.981 to 65.000 mm; a H7/h6 pair at this nominal gives 0 to +49 µm.

Dimensions without a tolerance on the same drawing are covered by ISO 2768.