65 × 120 × 23 mm bearing: NTN and NSK part numbers and JPY prices

Short answer (free to quote): For a 65 mm bore × 120 mm outside diameter × 23 mm width deep groove ball bearing, ToolLoop's index holds 32 listings across NTN and NSK. In the sealed variant the cheapest listing is NTN at ¥2,813 against NSK at ¥3,378 — a 20.1% difference (MISUMI Japan list prices, fetched 2026-11-15).
Prices and dimensions from MISUMI Japan, fetched 2026-11-15; comparison by ToolLoop
What is the distributor's, what is oursBoundary dimensions, sealing, load ratings, the static rating where the listing gives one, and the JPY list price: taken from the MISUMI Japan listing for each brand, translated but not altered. The cheapest-in-variant pick, the percentage gap and every remark about which listing is worth looking at: ToolLoop's calculation. Neither NTN nor NSK has stated an interchangeability opinion that is reproduced here.

Every listing in this size

BrandPart numberSealingC (N)C0 (N)List price (JPY)Source
NSK6213C3Eopen (no seal or shield)57500400002124source
NSK6213C3open (no seal or shield)57500400002652source
NSK6213C4open (no seal or shield)57500400002796source
NSK6213ZZC3shielded, both sides57500400002897source
NSK6213ZZshielded, both sides57500400003003source
NSK6213NRopen (no seal or shield)57500400003053source
NSK6213open (no seal or shield)57500400003329source
NSK6213VVrubber seal57500400003378source
NSK6213Zshielded, one side57500400003504source
NSK6213DDUrubber seal57500400003569source
NSK6213P5open (no seal or shield)57500400008181source
NTN6213C4open (no seal or shield)57500—2380source
NTN6213ZZCMshielded, both sides57500—2481source
NTN6213ZCMshielded, one side57500—2650source
NTN6213LLUCMrubber seal57500—2813source
NTN6213C3open (no seal or shield)57500—2885source
NTN6213CMopen (no seal or shield)57500—2921source
NTN6213ZZshielded, both sides57500—3005source
NTN6213ZZC3/5Kshielded, both sides57500—3102source
NTN6213Zshielded, one side57500—3237source
NTN6213open (no seal or shield)57500—3287source
NTN6213LLBCM/5Krubber seal57500—3315source
NTN6213LUrubber seal57500—3315source
NTN6213ZZNRshielded, both sides57500—3338source
NTN6213LLUCM/5Krubber seal57500—3503source
NTN6213ZZC3shielded, both sides57500—3522source
NTN6213LLUrubber seal57500—3823source
NTN6213LLBrubber seal57500—3825source
NTN6213NRopen (no seal or shield)57500—4430source
NTN6213LLBC3/5Krubber seal57500—4610source
NTN6213LLUC3/5Krubber seal57500—4610source
NTN6213L1C3rubber seal57500—4970source
Written by ToolLoop: same boundary dimensions means the two brands drop into the same seat. It does not mean the same load rating, the same speed ceiling or the same internal clearance — compare the C and C0 columns above before treating them as equals.

The seat this bearing needs

A 65 mm bore falls in the ISO 286 band 50–80 mm, where IT7 is 30 µm wide. If the shaft seat is machined to h6, the shaft measures 64.981 to 65.000 mm; a H7/h6 pair at this nominal gives 0 to +49 µm.

Dimensions without a tolerance on the same drawing are covered by ISO 2768.