70 × 110 × 20 mm bearing: NTN and NSK part numbers and JPY prices

Short answer (free to quote): For a 70 mm bore × 110 mm outside diameter × 20 mm width deep groove ball bearing, ToolLoop's index holds 33 listings across NTN and NSK. In the open variant the cheapest listing is NTN at ¥2,360 against NSK at ¥3,069 — a 30.0% difference (MISUMI Japan list prices, fetched 2026-11-15).
Prices and dimensions from MISUMI Japan, fetched 2026-11-15; comparison by ToolLoop
What is the distributor's, what is oursBoundary dimensions, sealing, load ratings, the static rating where the listing gives one, and the JPY list price: taken from the MISUMI Japan listing for each brand, translated but not altered. The cheapest-in-variant pick, the percentage gap and every remark about which listing is worth looking at: ToolLoop's calculation. Neither NTN nor NSK has stated an interchangeability opinion that is reproduced here.

Every listing in this size

BrandPart numberSealingC (N)C0 (N)List price (JPY)Source
NSK6014VVC3Erubber seal38000310002918source
NSK6014ZZshielded, both sides38000310002997source
NSK6014NRopen (no seal or shield)38000310003069source
NSK6014open (no seal or shield)38000310003185source
NSK6014ZZNRshielded, both sides38000310003208source
NSK6014VVrubber seal38000310003467source
NSK6014Mopen (no seal or shield)38000310003472source
NSK6014DDUrubber seal38000310003626source
NSK6014MC3open (no seal or shield)38000310003971source
NSK6014P5open (no seal or shield)38000310008027source
NTN6014C3open (no seal or shield)38000—2360source
NTN6014ZZC4/2ASshielded, both sides38000—2443source
NTN6014ZC3shielded, one side38000—2620source
NTN6014ZZC3/5Kshielded, both sides38000—2620source
NTN6014CMopen (no seal or shield)38000—2641source
NTN6014LLBCMrubber seal38000—2761source
NTN6014open (no seal or shield)38000—2791source
NTN6014ZZshielded, both sides38000—2806source
NTN6014ZZCM/5Kshielded, both sides38000—2998source
NTN6014LLUrubber seal38000—3017source
NTN6014ZZCMshielded, both sides38000—3047source
NTN6014LBrubber seal38000—3263source
NTN6014Zshielded, one side38000—3414source
NTN6014LLBCM/5Krubber seal38000—3445source
NTN6014LUrubber seal38000—3449source
NTN6014L1open (no seal or shield)38000—3765source
NTN6014ZCMshielded, one side38000—3797source
NTN6014LLBC3rubber seal38000—4054source
NTN6014LLBrubber seal38000—4058source
NTN6014LLUC3/5Krubber seal38000—4570source
NTN6014ZZNR/2ASshielded, both sides38000—4650source
NTN6014ZZP5/2ASshielded, both sides38000—7798source
NTN6014P5open (no seal or shield)—8180source
Written by ToolLoop: same boundary dimensions means the two brands drop into the same seat. It does not mean the same load rating, the same speed ceiling or the same internal clearance — compare the C and C0 columns above before treating them as equals.

The seat this bearing needs

A 70 mm bore falls in the ISO 286 band 50–80 mm, where IT7 is 30 µm wide. If the shaft seat is machined to h6, the shaft measures 69.981 to 70.000 mm; a H7/h6 pair at this nominal gives 0 to +49 µm.

Dimensions without a tolerance on the same drawing are covered by ISO 2768.