75 × 130 × 25 mm bearing: NTN and NSK part numbers and JPY prices

Short answer (free to quote): For a 75 mm bore × 130 mm outside diameter × 25 mm width deep groove ball bearing, ToolLoop's index holds 29 listings across NTN and NSK. In the sealed variant the cheapest listing is NTN at ¥3,321 against NSK at ¥4,524 — a 36.2% difference (MISUMI Japan list prices, fetched 2026-11-15).
Prices and dimensions from MISUMI Japan, fetched 2026-11-15; comparison by ToolLoop
What is the distributor's, what is oursBoundary dimensions, sealing, load ratings, the static rating where the listing gives one, and the JPY list price: taken from the MISUMI Japan listing for each brand, translated but not altered. The cheapest-in-variant pick, the percentage gap and every remark about which listing is worth looking at: ToolLoop's calculation. Neither NTN nor NSK has stated an interchangeability opinion that is reproduced here.

Every listing in this size

BrandPart numberSealingC (N)C0 (N)List price (JPY)Source
NSK6215C3Eopen (no seal or shield)66000495002815source
NSK6215Zshielded, one side66000495003575source
NSK6215NRopen (no seal or shield)66000495003987source
NSK6215ZZshielded, both sides66000495004110source
NSK6215MC3open (no seal or shield)66000495004255source
NSK6215Mopen (no seal or shield)66000495004332source
NSK6215DDUrubber seal66000495004524source
NSK6215P5open (no seal or shield)66000495009659source
NTN6215CMopen (no seal or shield)66000—3156source
NTN6215Zshielded, one side66000—3195source
NTN6215ZZCMshielded, both sides66000—3235source
NTN6215LLBCMrubber seal66000—3321source
NTN6215ZZC3/5Kshielded, both sides66000—3334source
NTN6215C3open (no seal or shield)66000—3349source
NTN6215LLUCMrubber seal66000—3497source
NTN6215open (no seal or shield)66000—3590source
NTN6215ZZCM/5Kshielded, both sides66000—3631source
NTN6215ZZC3shielded, both sides66000—3645source
NTN6215LLUrubber seal66000—3713source
NTN6215LLUCM/5Krubber seal66000—3895source
NTN6215ZZshielded, both sides66000—3956source
NTN6215ZCMshielded, one side66000—3957source
NTN6215LLBCM/5Krubber seal66000—4105source
NTN6215LLUC3/5Krubber seal66000—4105source
NTN6215ZC3shielded, one side66000—4830source
NTN6215LUrubber seal66000—5180source
NTN6215LLBrubber seal66000—5256source
NTN6215ZZNR/2ASshielded, both sides66000—5280source
NTN6215L1C3rubber seal—5330source
Written by ToolLoop: same boundary dimensions means the two brands drop into the same seat. It does not mean the same load rating, the same speed ceiling or the same internal clearance — compare the C and C0 columns above before treating them as equals.

The seat this bearing needs

A 75 mm bore falls in the ISO 286 band 50–80 mm, where IT7 is 30 µm wide. If the shaft seat is machined to h6, the shaft measures 74.981 to 75.000 mm; a H7/h6 pair at this nominal gives 0 to +49 µm.

Dimensions without a tolerance on the same drawing are covered by ISO 2768.