75 × 160 × 37 mm bearing: NTN and NSK part numbers and JPY prices

Short answer (free to quote): For a 75 mm bore × 160 mm outside diameter × 37 mm width deep groove ball bearing, ToolLoop's index holds 27 listings across NTN and NSK. In the open variant the cheapest listing is NSK at ¥5,694 against NTN at ¥6,672 — a 14.7% difference (MISUMI Japan list prices, fetched 2026-11-15).
Prices and dimensions from MISUMI Japan, fetched 2026-11-15; comparison by ToolLoop
What is the distributor's, what is oursBoundary dimensions, sealing, load ratings, the static rating where the listing gives one, and the JPY list price: taken from the MISUMI Japan listing for each brand, translated but not altered. The cheapest-in-variant pick, the percentage gap and every remark about which listing is worth looking at: ToolLoop's calculation. Neither NTN nor NSK has stated an interchangeability opinion that is reproduced here.

Every listing in this size

BrandPart numberSealingC (N)C0 (N)List price (JPY)Source
NSK6315C3Eopen (no seal or shield)113000770005694source
NSK6315C3open (no seal or shield)113000770006960source
NSK6315NRopen (no seal or shield)113000770007607source
NSK6315ZZshielded, both sides113000770007685source
NSK6315VVC3rubber seal113000770007791source
NSK6315ZZC3shielded, both sides113000770007821source
NSK6315open (no seal or shield)113000770008475source
NSK6315VVrubber seal113000770009645source
NSK6315Mopen (no seal or shield)1130007700010460source
NSK6315P5open (no seal or shield)1130007700023138source
NTN6315open (no seal or shield)113000—6672source
NTN6315ZCMshielded, one side113000—6960source
NTN6315NRopen (no seal or shield)113000—7353source
NTN6315C3open (no seal or shield)113000—7603source
NTN6315ZZC3/5Kshielded, both sides113000—7616source
NTN6315ZZC4/5Kshielded, both sides113000—7980source
NTN6315LLUrubber seal113000—8272source
NTN6315LLUC3/5Krubber seal113000—8309source
NTN6315ZZC3shielded, both sides113000—8415source
NTN6315LLBCMrubber seal113000—8439source
NTN6315Zshielded, one side113000—8767source
NTN6315LLBC3rubber seal113000—8936source
NTN6315ZZCM/5Kshielded, both sides113000—9116source
NTN6315LLBC3/5Krubber seal113000—9311source
NTN6315LLBCM/5Krubber seal113000—9311source
NTN6315L1C3open (no seal or shield)113000—9500source
NTN6315LLBrubber seal113000—9841source
Written by ToolLoop: same boundary dimensions means the two brands drop into the same seat. It does not mean the same load rating, the same speed ceiling or the same internal clearance — compare the C and C0 columns above before treating them as equals.

The seat this bearing needs

A 75 mm bore falls in the ISO 286 band 50–80 mm, where IT7 is 30 µm wide. If the shaft seat is machined to h6, the shaft measures 74.981 to 75.000 mm; a H7/h6 pair at this nominal gives 0 to +49 µm.

Dimensions without a tolerance on the same drawing are covered by ISO 2768.