90 × 160 × 30 mm bearing: NTN and NSK part numbers and JPY prices

Short answer (free to quote): For a 90 mm bore × 160 mm outside diameter × 30 mm width deep groove ball bearing, ToolLoop's index holds 27 listings across NTN and NSK. In the sealed variant the cheapest listing is NTN at ¥5,881 against NSK at ¥6,614 — a 12.5% difference (MISUMI Japan list prices, fetched 2026-11-15).
Prices and dimensions from MISUMI Japan, fetched 2026-11-15; comparison by ToolLoop
What is the distributor's, what is oursBoundary dimensions, sealing, load ratings, the static rating where the listing gives one, and the JPY list price: taken from the MISUMI Japan listing for each brand, translated but not altered. The cheapest-in-variant pick, the percentage gap and every remark about which listing is worth looking at: ToolLoop's calculation. Neither NTN nor NSK has stated an interchangeability opinion that is reproduced here.

Every listing in this size

BrandPart numberSealingC (N)C0 (N)List price (JPY)Source
NSK6218open (no seal or shield)96000715005283source
NSK6218ZZCMshielded, both sides96000715005641source
NSK6218Zshielded, one side96000715005730source
NSK6218C4open (no seal or shield)96000715005909source
NSK6218NRopen (no seal or shield)96000715006151source
NSK6218VVrubber seal96000715006614source
NSK6218ZZshielded, both sides96000715006706source
NSK6218Mopen (no seal or shield)96000715008279source
NSK6218P5open (no seal or shield)960007150019631source
NTN6218C4open (no seal or shield)96000—5141source
NTN6218ZZCMshielded, both sides96000—5322source
NTN6218CMopen (no seal or shield)96000—5422source
NTN6218C3open (no seal or shield)96000—5698source
NTN6218LLUCMrubber seal96000—5881source
NTN6218open (no seal or shield)96000—6051source
NTN6218LLBCMrubber seal96000—6323source
NTN6218ZC4shielded, one side96000—6518source
NTN6218ZC3shielded, one side96000—6562source
NTN6218ZZCM/5Kshielded, both sides96000—6562source
NTN6218ZZshielded, both sides96000—6784source
NTN6218ZZC3/5Kshielded, both sides96000—6940source
NTN6218NRopen (no seal or shield)96000—7050source
NTN6218LLBCM/5Krubber seal96000—7150source
NTN6218LLBrubber seal96000—7442source
NTN6218ZNRshielded, one side96000—7750source
NTN6218ZZNR/2ASshielded, both sides96000—7750source
NTN6218LLBC3/5Krubber seal96000—8697source
Written by ToolLoop: same boundary dimensions means the two brands drop into the same seat. It does not mean the same load rating, the same speed ceiling or the same internal clearance — compare the C and C0 columns above before treating them as equals.

The seat this bearing needs

A 90 mm bore falls in the ISO 286 band 80–120 mm, where IT7 is 35 µm wide. If the shaft seat is machined to h6, the shaft measures 89.978 to 90.000 mm; a H7/h6 pair at this nominal gives 0 to +57 µm.

Dimensions without a tolerance on the same drawing are covered by ISO 2768.