10 × 26 × 8 mm bearing: NTN and NSK part numbers and JPY prices

Short answer (free to quote): For a 10 mm bore × 26 mm outside diameter × 8 mm width deep groove ball bearing, ToolLoop's index holds 40 listings across NTN and NSK. In the sealed variant the cheapest listing is NSK at ¥338 against NTN at ¥460 — a 26.5% difference (MISUMI Japan list prices, fetched 2026-11-15).
Prices and dimensions from MISUMI Japan, fetched 2026-11-15; comparison by ToolLoop
What is the distributor's, what is oursBoundary dimensions, sealing, load ratings, the static rating where the listing gives one, and the JPY list price: taken from the MISUMI Japan listing for each brand, translated but not altered. The cheapest-in-variant pick, the percentage gap and every remark about which listing is worth looking at: ToolLoop's calculation. Neither NTN nor NSK has stated an interchangeability opinion that is reproduced here.

Every listing in this size

BrandPart numberSealingC (N)C0 (N)List price (JPY)Source
NSK6000VVC3Erubber seal45501970338source
NSK6000ZZshielded, both sides45501970370source
NSK6000ZZC3shielded, both sides45501970386source
NSK6000NRopen (no seal or shield)45501970398source
NSK6000open (no seal or shield)45501970428source
NSK6000VVrubber seal45501970437source
NSK6000ZZNRshielded, both sides45501970451source
NSK6000Zshielded, one side45501970463source
NSK6000DDUrubber seal45501970479source
NSK6000-H-20T1XDDrubber seal45501970632source
NSK6000U-H-20T1Xopen (no seal or shield)45501970832source
NSK6000-H-ZZU76UG2shielded, both sides455019701652source
NSK6000L11-H-20DDrubber seal455019702197source
NTN6000ZZCMshielded, both sides4550—409source
NTN6000ZZCM/5Kshielded, both sides4550—424source
NTN6000Zshielded, one side4550—426source
NTN6000ZZshielded, both sides4550—426source
NTN6000ZCMshielded, one side4550—452source
NTN6000LLUCMrubber seal4550—460source
NTN6000LLBrubber seal4550—469source
NTN6000LLUC3rubber seal4550—469source
NTN6000ZZNRshielded, both sides4550—475source
NTN6000LLUCM/5Krubber seal4550—476source
NTN6000LLUrubber seal4550—493source
NTN6000open (no seal or shield)4550—502source
NTN6000CMopen (no seal or shield)4550—537source
NTN6000C3open (no seal or shield)4550—559source
NTN6000LLUC3/5Krubber seal4550—588source
NTN6000ZC3shielded, one side4550—589source
NTN6000LLBC3rubber seal4550—605source
NTN6000LLBCMrubber seal4550—629source
NTN6000ZZC3/5Kshielded, both sides4550—630source
NTN6000LLU/LP03rubber seal4550—661source
NTN6000LLBCM/5Krubber seal4550—664source
NTN6000LBrubber seal4550—681source
NTN6000ZZC3shielded, both sides4550—693source
NTN6000LUrubber seal4550—736source
NTN6000ZZ/LP03shielded, both sides4550—756source
NTN6000LLB/LP03rubber seal4550—940source
NTN6000P5open (no seal or shield)4550—1280source
Written by ToolLoop: same boundary dimensions means the two brands drop into the same seat. It does not mean the same load rating, the same speed ceiling or the same internal clearance — compare the C and C0 columns above before treating them as equals.

The seat this bearing needs

A 10 mm bore falls in the ISO 286 band 6–10 mm, where IT7 is 15 µm wide. If the shaft seat is machined to h6, the shaft measures 9.991 to 10.000 mm; a H7/h6 pair at this nominal gives 0 to +24 µm.

Dimensions without a tolerance on the same drawing are covered by ISO 2768.