10 × 30 × 9 mm bearing: NTN and NSK part numbers and JPY prices

Short answer (free to quote): For a 10 mm bore × 30 mm outside diameter × 9 mm width deep groove ball bearing, ToolLoop's index holds 47 listings across NTN and NSK. In the open variant the cheapest listing is NSK at ¥255 against NTN at ¥322 — a 20.8% difference (MISUMI Japan list prices, fetched 2026-11-15).
Prices and dimensions from MISUMI Japan, fetched 2026-11-15; comparison by ToolLoop
What is the distributor's, what is oursBoundary dimensions, sealing, load ratings, the static rating where the listing gives one, and the JPY list price: taken from the MISUMI Japan listing for each brand, translated but not altered. The cheapest-in-variant pick, the percentage gap and every remark about which listing is worth looking at: ToolLoop's calculation. Neither NTN nor NSK has stated an interchangeability opinion that is reproduced here.

Every listing in this size

BrandPart numberSealingC (N)C0 (N)List price (JPY)Source
NSK6200C3open (no seal or shield)51002390255source
NSK6200DDUC3rubber seal51002390318source
NSK6200open (no seal or shield)51002390334source
NSK6200ZZshielded, both sides51002390342source
NSK6200ZZC3shielded, both sides51002390342source
NSK6200VVC3rubber seal51002390343source
NSK6200NRopen (no seal or shield)51002390369source
NSK6200DDUrubber seal51002390373source
NSK6200VVrubber seal51002390373source
NSK6200Zshielded, one side51002390387source
NSK6200ZZNRshielded, both sides51002390408source
NSK6200-H-20T1XZZshielded, both sides51002390860source
NSK6200-H-20T1XDDUrubber seal51002390915source
NSK6200U-H-20T1Xopen (no seal or shield)51002390992source
NSK6200L11DDUrubber seal510023901241source
NSK6200P5open (no seal or shield)510023901258source
NSK6200-H-ZZU76UG26shielded, both sides510023901506source
NTN6200CMopen (no seal or shield)5100—322source
NTN6200LLBCMrubber seal5100—363source
NTN6200ZZCM/5Kshielded, both sides5100—364source
NTN6200Zshielded, one side5100—366source
NTN6200ZZNR/2ASshielded, both sides5100—379source
NTN6200ZCMshielded, one side5100—414source
NTN6200open (no seal or shield)5100—425source
NTN6200C3open (no seal or shield)5100—431source
NTN6200ZZCM/L448shielded, both sides5100—445source
NTN6200LLBrubber seal5100—446source
NTN6200LLUrubber seal5100—446source
NTN6200ZZNRshielded, both sides5100—457source
NTN6200LLBC3rubber seal5100—462source
NTN6200LLBCM/5Krubber seal5100—493source
NTN6200ZZshielded, both sides5100—495source
NTN6200LLUC3/5Krubber seal5100—501source
NTN6200ZZCMshielded, both sides5100—513source
NTN6200ZZC3/5Kshielded, both sides5100—522source
NTN6200LLUC3rubber seal5100—547source
NTN6200LLUCM/5Krubber seal5100—559source
NTN6200ZZC3shielded, both sides5100—573source
NTN6200LLUCMrubber seal5100—586source
NTN6200LBrubber seal5100—590source
NTN6200LLBC3/5Krubber seal5100—684source
NTN6200ZZC4/5Kshielded, both sides5100—780source
NTN6200NRopen (no seal or shield)5100—790source
NTN6200ZZ/LP03shielded, both sides5100—830source
NTN6200LLBP5rubber seal5100—836source
NTN6200LLUNR/2ASrubber seal5100—840source
NTN6200LLU/LP03rubber seal5100—870source
Written by ToolLoop: same boundary dimensions means the two brands drop into the same seat. It does not mean the same load rating, the same speed ceiling or the same internal clearance — compare the C and C0 columns above before treating them as equals.

The seat this bearing needs

A 10 mm bore falls in the ISO 286 band 6–10 mm, where IT7 is 15 µm wide. If the shaft seat is machined to h6, the shaft measures 9.991 to 10.000 mm; a H7/h6 pair at this nominal gives 0 to +24 µm.

Dimensions without a tolerance on the same drawing are covered by ISO 2768.