15 × 32 × 9 mm bearing: NTN and NSK part numbers and JPY prices

Short answer (free to quote): For a 15 mm bore × 32 mm outside diameter × 9 mm width deep groove ball bearing, ToolLoop's index holds 57 listings across NTN and NSK. In the sealed variant the cheapest listing is NSK at ¥415 against NTN at ¥472 — a 12.1% difference (MISUMI Japan list prices, fetched 2026-11-15).
Prices and dimensions from MISUMI Japan, fetched 2026-11-15; comparison by ToolLoop
What is the distributor's, what is oursBoundary dimensions, sealing, load ratings, the static rating where the listing gives one, and the JPY list price: taken from the MISUMI Japan listing for each brand, translated but not altered. The cheapest-in-variant pick, the percentage gap and every remark about which listing is worth looking at: ToolLoop's calculation. Neither NTN nor NSK has stated an interchangeability opinion that is reproduced here.

Every listing in this size

BrandPart numberSealingC (N)C0 (N)List price (JPY)Source
NSK6002open (no seal or shield)56002830411source
NSK6002VVC3rubber seal56002830415source
NSK6002ZZshielded, both sides56002830417source
NSK6002VVC3Erubber seal56002830431source
NSK6002ZZC3shielded, both sides56002830449source
NSK6002ZZNRshielded, both sides56002830466source
NSK6002C3Eopen (no seal or shield)56002830487source
NSK6002VVrubber seal56002830488source
NSK6002NRopen (no seal or shield)56002830499source
NSK6002Zshielded, one side56002830517source
NSK6002DDUC3Erubber seal56002830518source
NSK6002DDUrubber seal56002830535source
NSK6002DDUNRrubber seal56002830584source
NSK6002DUCMrubber seal56002830665source
NSK6002-H-20T1XDDUrubber seal56002830865source
NSK6002-H-20T1XZZshielded, both sides56002830982source
NSK6002-H-ZZU76UG6shielded, both sides560028301619source
NSK6002L11-H-20DDUrubber seal560028303380source
NTN6002U1open (no seal or shield)5600—416source
NTN6002ZZCMshielded, both sides5600—441source
NTN6002LLBCM/5Krubber seal5600—472source
NTN6002ZC3shielded, one side5600—475source
NTN6002ZZCM/5Kshielded, both sides5600—492source
NTN6002Zshielded, one side5600—494source
NTN6002ZZshielded, both sides5600—494source
NTN6002LLBrubber seal5600—501source
NTN6002LLUrubber seal5600—527source
NTN6002CMopen (no seal or shield)5600—535source
NTN6002LLUCM/5Krubber seal5600—535source
NTN6002open (no seal or shield)5600—537source
NTN6002ZZC3shielded, both sides5600—544source
NTN6002LUrubber seal5600—550source
NTN6002ZZNR/2ASshielded, both sides5600—558source
NTN6002C3open (no seal or shield)5600—586source
NTN6002ZCMshielded, one side5600—604source
NTN6002LLUC4rubber seal5600—657source
NTN6002LLUNRrubber seal5600—686source
NTN6002LLBCMrubber seal5600—687source
NTN6002ZZC3/5Kshielded, both sides5600—695source
NTN6002LLB/5Krubber seal5600—701source
NTN6002LLUCMrubber seal5600—734source
NTN6002LLUC3/5Krubber seal5600—762source
NTN6002LLBC3/5Krubber seal5600—768source
NTN6002LLUC3rubber seal5600—823source
NTN6002ZZC4/5Kshielded, both sides5600—850source
NTN6002ZZNRshielded, both sides5600—851source
NTN6002NRopen (no seal or shield)5600—860source
NTN6002LBrubber seal5600—890source
NTN6002ZNRshielded, one side5600—900source
NTN6002ZZNRC3/2ASshielded, both sides5600—900source
NTN6002LLBNR/2ASrubber seal5600—940source
NTN6002ZZ/LP03shielded, both sides5600—940source
NTN6002LLB/LP03rubber seal5600—980source
NTN6002LLU/LP03rubber seal5600—980source
NTN6002LLBP5rubber seal5600—1111source
NTN6002LLBP5/2ASrubber seal5600—1319source
NTN6002P5open (no seal or shield)5600—1344source
Written by ToolLoop: same boundary dimensions means the two brands drop into the same seat. It does not mean the same load rating, the same speed ceiling or the same internal clearance — compare the C and C0 columns above before treating them as equals.

The seat this bearing needs

A 15 mm bore falls in the ISO 286 band 10–18 mm, where IT7 is 18 µm wide. If the shaft seat is machined to h6, the shaft measures 14.989 to 15.000 mm; a H7/h6 pair at this nominal gives 0 to +29 µm.

Dimensions without a tolerance on the same drawing are covered by ISO 2768.