15 × 35 × 11 mm bearing: NTN and NSK part numbers and JPY prices

Short answer (free to quote): For a 15 mm bore × 35 mm outside diameter × 11 mm width deep groove ball bearing, ToolLoop's index holds 54 listings across NTN and NSK. In the open variant the cheapest listing is NSK at ¥282 against NTN at ¥358 — a 21.2% difference (MISUMI Japan list prices, fetched 2026-11-15).
Prices and dimensions from MISUMI Japan, fetched 2026-11-15; comparison by ToolLoop
What is the distributor's, what is oursBoundary dimensions, sealing, load ratings, the static rating where the listing gives one, and the JPY list price: taken from the MISUMI Japan listing for each brand, translated but not altered. The cheapest-in-variant pick, the percentage gap and every remark about which listing is worth looking at: ToolLoop's calculation. Neither NTN nor NSK has stated an interchangeability opinion that is reproduced here.

Every listing in this size

BrandPart numberSealingC (N)C0 (N)List price (JPY)Source
NSK6202C3Eopen (no seal or shield)76503750282source
NSK6202NRopen (no seal or shield)76503750323source
NSK6202ZZshielded, both sides76503750386source
NSK6202ZZC3shielded, both sides76503750386source
NSK6202open (no seal or shield)76503750401source
NSK6202ZZCMshielded, both sides76503750404source
NSK6202DDUNRrubber seal76503750420source
NSK6202ZZNRshielded, both sides76503750432source
NSK6202DDUrubber seal76503750437source
NSK6202VVrubber seal76503750437source
NSK6202Zshielded, one side76503750463source
NSK6202-H-20T1XZZshielded, both sides765037501001source
NSK6202L11DDUrubber seal765037501013source
NSK6202U-H-20T1Xopen (no seal or shield)765037501104source
NSK6202-H-ZZU76UG2shielded, both sides765037501839source
NSK6202L11-H-20DDUrubber seal765037504679source
NTN6202CMopen (no seal or shield)7750—358source
NTN6202ZZCMshielded, both sides7750—409source
NTN6202ZZCM/5Kshielded, both sides7750—424source
NTN6202LLUCM/5Krubber seal7750—456source
NTN6202JR2C3open (no seal or shield)7750—457source
NTN6202LLBCM/5Krubber seal7750—469source
NTN6202LLUC3rubber seal7750—477source
NTN6202ZZC4/5Kshielded, both sides7750—488source
NTN6202ZZCM/L448shielded, both sides7750—516source
NTN6202LLBrubber seal7750—527source
NTN6202LLUrubber seal7750—527source
NTN6202C3open (no seal or shield)7750—534source
NTN6202ZZNRshielded, both sides7750—541source
NTN6202ZCMshielded, one side7750—615source
NTN6202LLUC3/5Krubber seal7750—623source
NTN6202ZZC3shielded, both sides7750—631source
NTN6202Zshielded, one side7750—633source
NTN6202ZZC3/5Kshielded, both sides7750—633source
NTN6202ZZshielded, both sides7750—635source
NTNEC-6202LLBC3/2ASrubber seal7750—639source
NTN6202LLBCMrubber seal7750—656source
NTN6202LUrubber seal7750—656source
NTN6202LLUNRrubber seal7750—658source
NTN6202LLUCMrubber seal7750—664source
NTN6202LBrubber seal7750—681source
NTN6202LLBC3rubber seal7750—681source
NTN6202ZZ/LP03shielded, both sides7750—681source
NTN6202LLBC3/5Krubber seal7750—692source
NTN6202ZZNR/2ASshielded, both sides7750—705source
NTN6202ZNRshielded, one side7750—729source
NTN6202NRopen (no seal or shield)7750—820source
NTN6202ZC3shielded, one side7750—820source
NTN6202LLBNR/2ASrubber seal7750—890source
NTN6202LLU/LP03rubber seal7750—940source
NTNEC-6202LLBC3/5Krubber seal7750—960source
NTN6202ZZP5shielded, both sides7750—1007source
NTN6202ZZP5/2ASshielded, both sides7750—1160source
NTN6202P4open (no seal or shield)7750—1389source
Written by ToolLoop: same boundary dimensions means the two brands drop into the same seat. It does not mean the same load rating, the same speed ceiling or the same internal clearance — compare the C and C0 columns above before treating them as equals.

The seat this bearing needs

A 15 mm bore falls in the ISO 286 band 10–18 mm, where IT7 is 18 µm wide. If the shaft seat is machined to h6, the shaft measures 14.989 to 15.000 mm; a H7/h6 pair at this nominal gives 0 to +29 µm.

Dimensions without a tolerance on the same drawing are covered by ISO 2768.