15 × 42 × 13 mm bearing: NTN and NSK part numbers and JPY prices

Short answer (free to quote): For a 15 mm bore × 42 mm outside diameter × 13 mm width deep groove ball bearing, ToolLoop's index holds 36 listings across NTN and NSK. In the open variant the cheapest listing is NSK at ¥353 against NTN at ¥579 — a 39.0% difference (MISUMI Japan list prices, fetched 2026-11-15).
Prices and dimensions from MISUMI Japan, fetched 2026-11-15; comparison by ToolLoop
What is the distributor's, what is oursBoundary dimensions, sealing, load ratings, the static rating where the listing gives one, and the JPY list price: taken from the MISUMI Japan listing for each brand, translated but not altered. The cheapest-in-variant pick, the percentage gap and every remark about which listing is worth looking at: ToolLoop's calculation. Neither NTN nor NSK has stated an interchangeability opinion that is reproduced here.

Every listing in this size

BrandPart numberSealingC (N)C0 (N)List price (JPY)Source
NSK6302C3Eopen (no seal or shield)114005450353source
NSK6302NRopen (no seal or shield)114005450478source
NSK6302open (no seal or shield)114005450503source
NSK6302DDUrubber seal114005450533source
NSK6302VVrubber seal114005450533source
NSK6302ZZC3shielded, both sides114005450576source
NSK6302ZZNRshielded, both sides114005450585source
NSK6302ZCMshielded, one side114005450602source
NTN6302ZZC3/5Kshielded, both sides11400—419source
NTN6302ZZCMshielded, both sides11400—513source
NTN6302ZZshielded, both sides11400—539source
NTN6302ZZNRshielded, both sides11400—569source
NTN6302LLUCMrubber seal11400—570source
NTN6302CMopen (no seal or shield)11400—579source
NTN6302LLUC3/5Krubber seal11400—590source
NTN6302LLBrubber seal11400—638source
NTN6302ZZNR/2ASshielded, both sides11400—649source
NTN6302C3open (no seal or shield)11400—656source
NTN6302open (no seal or shield)11400—669source
NTN6302ZU1shielded, one side11400—679source
NTN6302ZZCM/5Kshielded, both sides11400—686source
NTN6302ZZ/5Kshielded, both sides11400—696source
NTN6302LLBCMrubber seal11400—699source
NTN6302Zshielded, one side11400—706source
NTN6302LLUCM/5Krubber seal11400—723source
NTN6302LLBCM/5Krubber seal11400—730source
NTN6302ZZC3shielded, both sides11400—734source
NTN6302LLU/LP03rubber seal11400—747source
NTN6302LLUrubber seal11400—776source
NTN6302LLUC3rubber seal11400—878source
NTN6302LLBC3/5Krubber seal11400—920source
NTN6302LUrubber seal11400—920source
NTN6302ZNRshielded, one side11400—930source
NTN6302LLUNR/2ASrubber seal11400—970source
NTN6302ZZ/LP03shielded, both sides11400—980source
NTN6302LLB/LP03rubber seal11400—1030source
Written by ToolLoop: same boundary dimensions means the two brands drop into the same seat. It does not mean the same load rating, the same speed ceiling or the same internal clearance — compare the C and C0 columns above before treating them as equals.

The seat this bearing needs

A 15 mm bore falls in the ISO 286 band 10–18 mm, where IT7 is 18 µm wide. If the shaft seat is machined to h6, the shaft measures 14.989 to 15.000 mm; a H7/h6 pair at this nominal gives 0 to +29 µm.

Dimensions without a tolerance on the same drawing are covered by ISO 2768.