17 × 47 × 14 mm bearing: NTN and NSK part numbers and JPY prices

Short answer (free to quote): For a 17 mm bore × 47 mm outside diameter × 14 mm width deep groove ball bearing, ToolLoop's index holds 37 listings across NTN and NSK. In the shielded variant the cheapest listing is NTN at ¥585 against NSK at ¥671 — a 14.7% difference (MISUMI Japan list prices, fetched 2026-11-15).
Prices and dimensions from MISUMI Japan, fetched 2026-11-15; comparison by ToolLoop
What is the distributor's, what is oursBoundary dimensions, sealing, load ratings, the static rating where the listing gives one, and the JPY list price: taken from the MISUMI Japan listing for each brand, translated but not altered. The cheapest-in-variant pick, the percentage gap and every remark about which listing is worth looking at: ToolLoop's calculation. Neither NTN nor NSK has stated an interchangeability opinion that is reproduced here.

Every listing in this size

BrandPart numberSealingC (N)C0 (N)List price (JPY)Source
NSK6303C3Eopen (no seal or shield)136006650453source
NSK6303NRopen (no seal or shield)136006650545source
NSK6303open (no seal or shield)136006650605source
NSK6303DDUrubber seal136006650645source
NSK6303VVrubber seal136006650663source
NSK6303ZZNRshielded, both sides136006650671source
NSK6303ZZC3shielded, both sides136006650699source
NSK6303P5open (no seal or shield)1360066501676source
NTN6303CMopen (no seal or shield)13500—491source
NTN6303ZZCMshielded, both sides13500—585source
NTN6303LLBCM/5Krubber seal13500—606source
NTN6303ZZshielded, both sides13500—648source
NTN6303ZCMshielded, one side13500—696source
NTN6303NRopen (no seal or shield)13500—713source
NTN6303C3open (no seal or shield)13500—722source
NTN6303open (no seal or shield)13500—724source
NTN6303LLUrubber seal13500—732source
NTN6303LBrubber seal13500—751source
NTN6303ZZNRshielded, both sides13500—766source
NTN6303ZZC3/5Kshielded, both sides13500—770source
NTN6303ZZCM/5Kshielded, both sides13500—776source
NTN6303ZZC3shielded, both sides13500—780source
NTN6303LLUCM/5Krubber seal13500—803source
NTN6303Zshielded, one side13500—805source
NTN6303ZC3shielded, one side13500—826source
NTN6303LLUCMrubber seal13500—844source
NTN6303LLBCMrubber seal13500—855source
NTN6303LLBNRrubber seal13500—863source
NTN6303LLBrubber seal13500—897source
NTN6303LLBC3/5Krubber seal13500—920source
NTN6303LLBC3rubber seal13500—937source
NTN6303ZZC4/5Kshielded, both sides13500—950source
NTN6303LLUC3/5Krubber seal13500—1000source
NTN6303ZNRshielded, one side13500—1010source
NTN6303LUZC4/2ASrubber seal13500—1050source
NTN6303ZZNR/2Ashielded, both sides13500—1074source
NTN6303LLBP5/2ASrubber seal13500—1760source
Written by ToolLoop: same boundary dimensions means the two brands drop into the same seat. It does not mean the same load rating, the same speed ceiling or the same internal clearance — compare the C and C0 columns above before treating them as equals.

The seat this bearing needs

A 17 mm bore falls in the ISO 286 band 10–18 mm, where IT7 is 18 µm wide. If the shaft seat is machined to h6, the shaft measures 16.989 to 17.000 mm; a H7/h6 pair at this nominal gives 0 to +29 µm.

Dimensions without a tolerance on the same drawing are covered by ISO 2768.