20 × 42 × 12 mm bearing: NTN and NSK part numbers and JPY prices

Short answer (free to quote): For a 20 mm bore × 42 mm outside diameter × 12 mm width deep groove ball bearing, ToolLoop's index holds 55 listings across NTN and NSK. In the sealed variant the cheapest listing is NSK at ¥404 against NTN at ¥550 — a 26.5% difference (MISUMI Japan list prices, fetched 2026-11-15).
Prices and dimensions from MISUMI Japan, fetched 2026-11-15; comparison by ToolLoop
What is the distributor's, what is oursBoundary dimensions, sealing, load ratings, the static rating where the listing gives one, and the JPY list price: taken from the MISUMI Japan listing for each brand, translated but not altered. The cheapest-in-variant pick, the percentage gap and every remark about which listing is worth looking at: ToolLoop's calculation. Neither NTN nor NSK has stated an interchangeability opinion that is reproduced here.

Every listing in this size

BrandPart numberSealingC (N)C0 (N)List price (JPY)Source
NSK6004C3Eopen (no seal or shield)94005000353source
NSK6004DDUC3Erubber seal94005000404source
NSK6004NRopen (no seal or shield)94005000460source
NSK6004ZZshielded, both sides94005000473source
NSK6004DUCMrubber seal94005000502source
NSK6004open (no seal or shield)94005000503source
NSK6004ZZC3shielded, both sides94005000504source
NSK6004VVrubber seal94005000552source
NSK6004ZZNRshielded, both sides94005000568source
NSK6004Zshielded, one side94005000583source
NSK6004DDUrubber seal94005000606source
NSK6004DDUNRrubber seal94005000749source
NSK6004U-H-20T1Xopen (no seal or shield)940050001196source
NSK6004-H-20T1XZZshielded, both sides940050001224source
NSK6004-H-20T1XDDUrubber seal940050001440source
NSK6004P5open (no seal or shield)940050002369source
NSK6004-H-ZZU76UG30shielded, both sides940050003312source
NSK6004L11-H-20DDUrubber seal940050005423source
NTN6004ZCMshielded, one side7900—409source
NTN6004ZZCMshielded, both sides7900—424source
NTN6004CMopen (no seal or shield)7900—450source
NTN6004ZZshielded, both sides7900—487source
NTN6004ZC3shielded, one side7900—532source
NTN6004Zshielded, one side7900—533source
NTN6004ZZCM/5Kshielded, both sides7900—534source
NTN6004LLUCM/5Krubber seal7900—550source
NTN6004LUrubber seal7900—581source
NTN6004ZZNRshielded, both sides7900—581source
NTN6004ZZNR/2ASshielded, both sides7900—586source
NTN6004LLBCM/5Krubber seal7900—603source
NTN6004LLBrubber seal7900—604source
NTN6004ZZ/LP03shielded, both sides7900—608source
NTN6004open (no seal or shield)9400—624source
NTN6004LLUC3rubber seal7900—631source
NTN6004C3open (no seal or shield)7900—648source
NTN6004LLUrubber seal7900—665source
NTN6004LLUNR/2ASrubber seal7900—672source
NTN6004LLUNRrubber seal7900—688source
NTN6004LLBCMrubber seal7900—701source
NTN6004LLBNR/2ASrubber seal7900—715source
NTN6004LLBNRrubber seal7900—716source
NTN6004LBrubber seal7900—764source
NTN6004ZZC3shielded, both sides7900—767source
NTN6004LLB/LP03rubber seal7900—768source
NTN6004LLUCMrubber seal7900—784source
NTN6004LLBC3rubber seal7900—792source
NTN6004NRopen (no seal or shield)7900—817source
NTN6004ZZC3/5Kshielded, both sides7900—821source
NTN6004LLUC3/5Krubber seal7900—835source
NTN6004ZZC4/5Kshielded, both sides7900—870source
NTN6004LLBC3/5Krubber seal7900—876source
NTN6004ZNRshielded, one side7900—930source
NTN6004P5open (no seal or shield)9400—1296source
NTN6004ZZP5/2ASshielded, both sides9400—1500source
NTN6004P4open (no seal or shield)9400—1910source
Written by ToolLoop: same boundary dimensions means the two brands drop into the same seat. It does not mean the same load rating, the same speed ceiling or the same internal clearance — compare the C and C0 columns above before treating them as equals.

The seat this bearing needs

A 20 mm bore falls in the ISO 286 band 18–30 mm, where IT7 is 21 µm wide. If the shaft seat is machined to h6, the shaft measures 19.987 to 20.000 mm; a H7/h6 pair at this nominal gives 0 to +34 µm.

Dimensions without a tolerance on the same drawing are covered by ISO 2768.