30 × 72 × 19 mm bearing: NTN and NSK part numbers and JPY prices

Short answer (free to quote): For a 30 mm bore × 72 mm outside diameter × 19 mm width deep groove ball bearing, ToolLoop's index holds 44 listings across NTN and NSK. In the shielded variant the cheapest listing is NTN at ¥942 against NSK at ¥1,034 — a 9.8% difference (MISUMI Japan list prices, fetched 2026-11-15).
Prices and dimensions from MISUMI Japan, fetched 2026-11-15; comparison by ToolLoop
What is the distributor's, what is oursBoundary dimensions, sealing, load ratings, the static rating where the listing gives one, and the JPY list price: taken from the MISUMI Japan listing for each brand, translated but not altered. The cheapest-in-variant pick, the percentage gap and every remark about which listing is worth looking at: ToolLoop's calculation. Neither NTN nor NSK has stated an interchangeability opinion that is reproduced here.

Every listing in this size

BrandPart numberSealingC (N)C0 (N)List price (JPY)Source
NSK6306C3Eopen (no seal or shield)2670015000878source
NSK6306ZZshielded, both sides26700150001034source
NSK6306open (no seal or shield)26700150001146source
NSK6306ZZC3shielded, both sides26700150001166source
NSK6306DDUrubber seal26700150001177source
NSK6306ZZNRshielded, both sides26700150001221source
NSK6306VVrubber seal26700150001224source
NSK6306P5open (no seal or shield)26700150003194source
NTN6306ZZC4shielded, both sides26700—942source
NTN6306C4open (no seal or shield)26700—968source
NTN6306C3open (no seal or shield)26700—1060source
NTN6306open (no seal or shield)26700—1063source
NTN6306CMopen (no seal or shield)26700—1079source
NTN6306LLUC3/5Krubber seal26700—1130source
NTN6306ZCMshielded, one side26700—1153source
NTN6306LLUCMrubber seal26700—1181source
NTN6306Zshielded, one side26700—1186source
NTN6306ZZshielded, both sides26700—1186source
NTN6306NRopen (no seal or shield)26700—1192source
NTN6306ZZNR/2ASshielded, both sides26700—1208source
NTN6306LLBCMrubber seal26700—1211source
NTN6306ZZCMshielded, both sides26700—1234source
NTN6306ZC3shielded, one side26700—1237source
NTN6306ZZC3/5Kshielded, both sides26700—1253source
NTN6306ZZCM/5Kshielded, both sides26700—1268source
NTN6306ZZC3shielded, both sides26700—1269source
NTN6306ZZNRshielded, both sides26700—1314source
NTN6306NRC3open (no seal or shield)26700—1330source
NTN6306LLBNR/2ASrubber seal26700—1333source
NTN6306LLUC4rubber seal26700—1384source
NTN6306LBrubber seal26700—1390source
NTN6306LLBCM/5Krubber seal26700—1390source
NTN6306LUrubber seal26700—1390source
NTN6306ZZ/LP03shielded, both sides26700—1391source
NTN6306LLBC3rubber seal26700—1396source
NTN6306LLUrubber seal26700—1398source
NTN6306LLUCM/5Krubber seal26700—1406source
NTN6306LLBrubber seal26700—1449source
NTN6306LLBNRrubber seal26700—1505source
NTN6306LLUC3rubber seal26700—1531source
NTN6306LLU/LP03rubber seal26700—1640source
NTN6306L1C3open (no seal or shield)26700—1897source
NTN6306LLBC3/5Krubber seal26700—1995source
NTN6306ZZC4/5Kshielded, both sides26700—2230source
Written by ToolLoop: same boundary dimensions means the two brands drop into the same seat. It does not mean the same load rating, the same speed ceiling or the same internal clearance — compare the C and C0 columns above before treating them as equals.

The seat this bearing needs

A 30 mm bore falls in the ISO 286 band 18–30 mm, where IT7 is 21 µm wide. If the shaft seat is machined to h6, the shaft measures 29.987 to 30.000 mm; a H7/h6 pair at this nominal gives 0 to +34 µm.

Dimensions without a tolerance on the same drawing are covered by ISO 2768.