35 × 55 × 10 mm bearing: NTN and NSK part numbers and JPY prices

Short answer (free to quote): For a 35 mm bore × 55 mm outside diameter × 10 mm width deep groove ball bearing, ToolLoop's index holds 28 listings across NTN and NSK. In the open variant the cheapest listing is NSK at ¥732 against NTN at ¥1,031 — a 29.0% difference (MISUMI Japan list prices, fetched 2026-11-15).
Prices and dimensions from MISUMI Japan, fetched 2026-11-15; comparison by ToolLoop
What is the distributor's, what is oursBoundary dimensions, sealing, load ratings, the static rating where the listing gives one, and the JPY list price: taken from the MISUMI Japan listing for each brand, translated but not altered. The cheapest-in-variant pick, the percentage gap and every remark about which listing is worth looking at: ToolLoop's calculation. Neither NTN nor NSK has stated an interchangeability opinion that is reproduced here.

Every listing in this size

BrandPart numberSealingC (N)C0 (N)List price (JPY)Source
NSK6907C3open (no seal or shield)106007250732source
NSK6907CMopen (no seal or shield)106007250773source
NSK6907C3Eopen (no seal or shield)106007250793source
NSK6907ZZC3shielded, both sides106007250809source
NSK6907VVC3rubber seal106007250946source
NSK6907DDUC3rubber seal106007250969source
NSK6907open (no seal or shield)1060072501050source
NSK6907Zshielded, one side1060072501077source
NSK6907ZZshielded, both sides1060072501208source
NSK6907DDUrubber seal1060072501227source
NSK6907ZZNRshielded, both sides1060072501318source
NSK6907VVrubber seal1060072501370source
NTN6907LLBC3rubber seal9550—965source
NTN6907ZZshielded, both sides9550—1018source
NTN6907open (no seal or shield)9550—1031source
NTN6907LLUrubber seal9550—1076source
NTN6907LLU/2ASrubber seal9550—1098source
NTN6907Zshielded, one side9550—1102source
NTN6907ZZNR/2ASshielded, both sides9550—1123source
NTN6907LLBC3/5Krubber seal9550—1177source
NTN6907LLBrubber seal9550—1235source
NTN6907ZZNRshielded, both sides9550—1237source
NTN6907ZZC3/5Kshielded, both sides9550—1250source
NTN6907LLB/2ASrubber seal9550—1271source
NTN6907NRopen (no seal or shield)9550—1280source
NTN6907LLU/5Krubber seal9550—1367source
NTN6907LLU/LP03rubber seal9550—1570source
NTN6907ZZP5/2ASshielded, both sides9550—2610source
Written by ToolLoop: same boundary dimensions means the two brands drop into the same seat. It does not mean the same load rating, the same speed ceiling or the same internal clearance — compare the C and C0 columns above before treating them as equals.

The seat this bearing needs

A 35 mm bore falls in the ISO 286 band 30–50 mm, where IT7 is 25 µm wide. If the shaft seat is machined to h6, the shaft measures 34.984 to 35.000 mm; a H7/h6 pair at this nominal gives 0 to +41 µm.

Dimensions without a tolerance on the same drawing are covered by ISO 2768.