40 × 90 × 23 mm bearing: NTN and NSK part numbers and JPY prices

Short answer (free to quote): For a 40 mm bore × 90 mm outside diameter × 23 mm width deep groove ball bearing, ToolLoop's index holds 50 listings across NTN and NSK. In the shielded variant the cheapest listing is NTN at ¥1,653 against NSK at ¥2,318 — a 40.2% difference (MISUMI Japan list prices, fetched 2026-11-15).
Prices and dimensions from MISUMI Japan, fetched 2026-11-15; comparison by ToolLoop
What is the distributor's, what is oursBoundary dimensions, sealing, load ratings, the static rating where the listing gives one, and the JPY list price: taken from the MISUMI Japan listing for each brand, translated but not altered. The cheapest-in-variant pick, the percentage gap and every remark about which listing is worth looking at: ToolLoop's calculation. Neither NTN nor NSK has stated an interchangeability opinion that is reproduced here.

Every listing in this size

BrandPart numberSealingC (N)C0 (N)List price (JPY)Source
NSK6308C4open (no seal or shield)40500240001542source
NSK6308C3open (no seal or shield)40500240002119source
NSK6308open (no seal or shield)40500240002273source
NSK6308ZZshielded, both sides40500240002318source
NSK6308ZZC3shielded, both sides40500240002375source
NSK6308VVrubber seal40500240002418source
NSK6308DDUC3rubber seal40500240002424source
NSK6308Mopen (no seal or shield)40500240002553source
NSK6308DDUrubber seal40500240002653source
NSK6308VVC3rubber seal40500240002653source
NSK6308ZZNRshielded, both sides40500240002653source
NSK6308L11DDUrubber seal40500240005081source
NSK6308P5open (no seal or shield)40500240006067source
NTN6308ZZC4shielded, both sides40500—1653source
NTN6308CMopen (no seal or shield)40500—1860source
NTN6308C4open (no seal or shield)40500—1862source
NTN6308NRopen (no seal or shield)40500—2060source
NTN6308ZZC4/5Kshielded, both sides40500—2067source
NTN6308open (no seal or shield)40500—2101source
NTN6308LLUCMrubber seal40500—2103source
NTN6308LBrubber seal40500—2190source
NTN6308LUrubber seal40500—2190source
NTN6308LLB/5Krubber seal40500—2227source
NTN6308ZZCMshielded, both sides40500—2231source
NTN6308C3open (no seal or shield)40500—2354source
NTN6308LLUC3/5Krubber seal40500—2371source
NTN6308ZZNR/2ASshielded, both sides40500—2376source
NTN6308ZZCM/5Kshielded, both sides40500—2430source
NTN6308L1C3open (no seal or shield)40500—2440source
NTN6308LLUNR/2ASrubber seal40500—2440source
NTN6308ZZC3/L448shielded, both sides40500—2440source
NTN6308LLUCM/5Krubber seal40500—2450source
NTN6308ZC3shielded, one side40500—2455source
NTN6308ZZC3/5Kshielded, both sides40500—2467source
NTN6308ZZC3shielded, both sides40500—2491source
NTN6308LLUrubber seal40500—2510source
NTN6308ZZshielded, both sides40500—2602source
NTN6308LLUC3rubber seal40500—2620source
NTN6308ZCMshielded, one side40500—2754source
NTN6308LLBCM/5Krubber seal40500—2760source
NTN6308ZZNRshielded, both sides40500—2812source
NTN6308LLBrubber seal40500—2813source
NTN6308LLBC3/5Krubber seal40500—2826source
NTN6308Zshielded, one side40500—2856source
NTN6308LLBC3rubber seal40500—2944source
NTN6308LLBCMrubber seal40500—3023source
NTN6308M8C3P6open (no seal or shield)40500—4500source
NTN6308ZZD2C3/5Kshielded, both sides40500—5410source
NTN6308LLBP5/2ASrubber seal40500—6337source
NTN6308ZZP5/2ASshielded, both sides40500—6580source
Written by ToolLoop: same boundary dimensions means the two brands drop into the same seat. It does not mean the same load rating, the same speed ceiling or the same internal clearance — compare the C and C0 columns above before treating them as equals.

The seat this bearing needs

A 40 mm bore falls in the ISO 286 band 30–50 mm, where IT7 is 25 µm wide. If the shaft seat is machined to h6, the shaft measures 39.984 to 40.000 mm; a H7/h6 pair at this nominal gives 0 to +41 µm.

Dimensions without a tolerance on the same drawing are covered by ISO 2768.