50 × 110 × 27 mm bearing: NTN and NSK part numbers and JPY prices

Short answer (free to quote): For a 50 mm bore × 110 mm outside diameter × 27 mm width deep groove ball bearing, ToolLoop's index holds 45 listings across NTN and NSK. In the sealed variant the cheapest listing is NTN at ¥2,772 against NSK at ¥3,362 — a 21.3% difference (MISUMI Japan list prices, fetched 2026-11-15).
Prices and dimensions from MISUMI Japan, fetched 2026-11-15; comparison by ToolLoop
What is the distributor's, what is oursBoundary dimensions, sealing, load ratings, the static rating where the listing gives one, and the JPY list price: taken from the MISUMI Japan listing for each brand, translated but not altered. The cheapest-in-variant pick, the percentage gap and every remark about which listing is worth looking at: ToolLoop's calculation. Neither NTN nor NSK has stated an interchangeability opinion that is reproduced here.

Every listing in this size

BrandPart numberSealingC (N)C0 (N)List price (JPY)Source
NSK6310C3Eopen (no seal or shield)62000385002725source
NSK6310C3open (no seal or shield)62000385002744source
NSK6310ZZshielded, both sides62000385002880source
NSK6310NRopen (no seal or shield)62000385002886source
NSK6310ZZNRshielded, both sides62000385003091source
NSK6310ZZC3shielded, both sides62000385003160source
NSK6310DDUrubber seal62000385003362source
NSK6310VVrubber seal62000385003491source
NSK6310MC3open (no seal or shield)62000385003675source
NSK6310Mopen (no seal or shield)62000385003862source
NSK6310Zshielded, one side62000385003946source
NSK6310P5open (no seal or shield)62000385008500source
NTN6310ZZC4shielded, both sides62000—2478source
NTN6310ZZC4/5Kshielded, both sides62000—2615source
NTN6310C4open (no seal or shield)62000—2664source
NTN6310LLBCMrubber seal62000—2772source
NTN6310NRopen (no seal or shield)62000—2832source
NTN6310ZCMshielded, one side62000—3065source
NTN6310ZZC3shielded, both sides62000—3084source
NTN6310LUrubber seal62000—3111source
NTN6310CMopen (no seal or shield)62000—3151source
NTN6310ZZC3/5Kshielded, both sides62000—3221source
NTN6310ZZCM/5Kshielded, both sides62000—3237source
NTN6310open (no seal or shield)62000—3299source
NTN6310LLUCMrubber seal62000—3305source
NTN6310LLUrubber seal62000—3339source
NTN6310LLUC3/5Krubber seal62000—3340source
NTN6310LLBCM/5Krubber seal62000—3462source
NTN6310ZZNR/2ASshielded, both sides62000—3468source
NTN6310LLUCM/5Krubber seal62000—3484source
NTN6310ZZCMshielded, both sides62000—3504source
NTN6310Zshielded, one side62000—3518source
NTN6310C3open (no seal or shield)62000—3521source
NTN6310LLUC3rubber seal62000—3527source
NTN6310ZZshielded, both sides62000—3682source
NTN6310ZZNRshielded, both sides62000—3798source
NTN6310LLBC3/5Krubber seal62000—3987source
NTN6310LLBrubber seal62000—4046source
NTN6310ZC3shielded, one side62000—4430source
NTN6310ZZCM/L448shielded, both sides62000—4430source
NTN6310NRC3open (no seal or shield)62000—4593source
NTN6310LLBC3rubber seal62000—4661source
NTN6310LBrubber seal62000—4710source
NTN6310LLBNR/2ASrubber seal62000—5090source
NTN6310M8C3P6open (no seal or shield)62000—5360source
Written by ToolLoop: same boundary dimensions means the two brands drop into the same seat. It does not mean the same load rating, the same speed ceiling or the same internal clearance — compare the C and C0 columns above before treating them as equals.

The seat this bearing needs

A 50 mm bore falls in the ISO 286 band 30–50 mm, where IT7 is 25 µm wide. If the shaft seat is machined to h6, the shaft measures 49.984 to 50.000 mm; a H7/h6 pair at this nominal gives 0 to +41 µm.

Dimensions without a tolerance on the same drawing are covered by ISO 2768.