50 × 80 × 16 mm bearing: NTN and NSK part numbers and JPY prices

Short answer (free to quote): For a 50 mm bore × 80 mm outside diameter × 16 mm width deep groove ball bearing, ToolLoop's index holds 44 listings across NTN and NSK. In the open variant the cheapest listing is NTN at ¥1,298 against NSK at ¥1,662 — a 28.0% difference (MISUMI Japan list prices, fetched 2026-11-15).
Prices and dimensions from MISUMI Japan, fetched 2026-11-15; comparison by ToolLoop
What is the distributor's, what is oursBoundary dimensions, sealing, load ratings, the static rating where the listing gives one, and the JPY list price: taken from the MISUMI Japan listing for each brand, translated but not altered. The cheapest-in-variant pick, the percentage gap and every remark about which listing is worth looking at: ToolLoop's calculation. Neither NTN nor NSK has stated an interchangeability opinion that is reproduced here.

Every listing in this size

BrandPart numberSealingC (N)C0 (N)List price (JPY)Source
NSK6010ZZC3Eshielded, both sides21800166001123source
NSK6010ZZC3shielded, both sides21800166001361source
NSK6010ZZshielded, both sides21800166001492source
NSK6010VVC3rubber seal21800166001522source
NSK6010open (no seal or shield)21800166001662source
NSK6010Zshielded, one side21800166001740source
NSK6010NRopen (no seal or shield)21800166001836source
NSK6010DDUNRrubber seal21800166001866source
NSK6010ZZNRshielded, both sides21800166001968source
NSK6010DDUrubber seal21800166002068source
NSK6010P5open (no seal or shield)21800166004082source
NSK6010-H-20ZZshielded, both sides218001660013980source
NSK6010-H-20DDUrubber seal218001660017971source
NTN6010C3open (no seal or shield)21800—1298source
NTN6010open (no seal or shield)21800—1453source
NTN6010ZZC3shielded, both sides21800—1458source
NTN6010CMopen (no seal or shield)21800—1484source
NTN6010LLBCMrubber seal21800—1538source
NTN6010ZZCM/5Kshielded, both sides21800—1546source
NTN6010LLUCMrubber seal21800—1595source
NTN6010LLUC3rubber seal21800—1604source
NTN6010ZZC4/5Kshielded, both sides21800—1610source
NTN6010LLUC3/5Krubber seal21800—1656source
NTN6010LLUrubber seal21800—1671source
NTN6010Zshielded, one side21800—1729source
NTN6010ZZNR/2ASshielded, both sides21800—1736source
NTN6010LUrubber seal21800—1740source
NTN6010ZNRshielded, one side21800—1790source
NTN6010LLUCM/5Krubber seal21800—1822source
NTN6010ZZshielded, both sides21800—1861source
NTN6010LLBCM/5Krubber seal21800—1876source
NTN6010LLBC3rubber seal21800—1898source
NTN6010LLBNR/2ASrubber seal21800—1920source
NTN6010LLUNR/2ASrubber seal21800—1920source
NTN6010ZZ/LP03shielded, both sides21800—1920source
NTN6010LLBrubber seal21800—1992source
NTN6010LLU/LP03rubber seal21800—2100source
NTN6010ZZC3/5Kshielded, both sides21800—2175source
NTN6010ZZNRshielded, both sides21800—2199source
NTN6010LLBC3/5Krubber seal21800—2613source
NTN6010ZCMshielded, one side21800—2654source
NTN6010ZZP5shielded, both sides21800—3998source
NTN6010ZZP5/2ASshielded, both sides21800—5370source
NTN6010P5open (no seal or shield)21800—5714source
Written by ToolLoop: same boundary dimensions means the two brands drop into the same seat. It does not mean the same load rating, the same speed ceiling or the same internal clearance — compare the C and C0 columns above before treating them as equals.

The seat this bearing needs

A 50 mm bore falls in the ISO 286 band 30–50 mm, where IT7 is 25 µm wide. If the shaft seat is machined to h6, the shaft measures 49.984 to 50.000 mm; a H7/h6 pair at this nominal gives 0 to +41 µm.

Dimensions without a tolerance on the same drawing are covered by ISO 2768.