60 × 110 × 22 mm bearing: NTN and NSK part numbers and JPY prices

Short answer (free to quote): For a 60 mm bore × 110 mm outside diameter × 22 mm width deep groove ball bearing, ToolLoop's index holds 43 listings across NTN and NSK. In the open variant the cheapest listing is NSK at ¥1,606 against NTN at ¥1,953 — a 17.8% difference (MISUMI Japan list prices, fetched 2026-11-15).
Prices and dimensions from MISUMI Japan, fetched 2026-11-15; comparison by ToolLoop
What is the distributor's, what is oursBoundary dimensions, sealing, load ratings, the static rating where the listing gives one, and the JPY list price: taken from the MISUMI Japan listing for each brand, translated but not altered. The cheapest-in-variant pick, the percentage gap and every remark about which listing is worth looking at: ToolLoop's calculation. Neither NTN nor NSK has stated an interchangeability opinion that is reproduced here.

Every listing in this size

BrandPart numberSealingC (N)C0 (N)List price (JPY)Source
NSK6212C3Eopen (no seal or shield)52500360001606source
NSK6212C4open (no seal or shield)52500360001955source
NSK6212C3open (no seal or shield)52500360001970source
NSK6212ZZshielded, both sides52500360002287source
NSK6212NRopen (no seal or shield)52500360002298source
NSK6212ZZC3shielded, both sides52500360002492source
NSK6212DDUrubber seal52500360002672source
NSK6212Zshielded, one side52500360002905source
NSK6212VVrubber seal52500360002962source
NSK6212P5open (no seal or shield)52500360006193source
NSK6212-H-20ZZshielded, both sides525003600029980source
NSK6212-H-20DDUrubber seal525003600039802source
NTN6212CMopen (no seal or shield)52500—1953source
NTN6212C3open (no seal or shield)52500—1965source
NTN6212ZC3shielded, one side52500—2230source
NTN6212ZC4shielded, one side52500—2230source
NTN6212ZZC4/5Kshielded, both sides52500—2230source
NTN6212NRopen (no seal or shield)52500—2290source
NTN6212ZCMshielded, one side52500—2330source
NTN6212open (no seal or shield)52500—2406source
NTN6212LLBC3rubber seal52500—2412source
NTN6212LLUC3/5Krubber seal52500—2440source
NTN6212LUrubber seal52500—2440source
NTN6212LLUCMrubber seal52500—2516source
NTN6212ZZCMshielded, both sides52500—2517source
NTN6212LLUrubber seal52500—2598source
NTN6212LBrubber seal52500—2632source
NTN6212ZZC3/5Kshielded, both sides52500—2656source
NTN6212ZZCM/5Kshielded, both sides52500—2667source
NTN6212ZZshielded, both sides52500—2680source
NTN6212LLUCM/5Krubber seal52500—2683source
NTN6212LLBNR/2ASrubber seal52500—2730source
NTN6212LLUNR/2ASrubber seal52500—2730source
NTN6212ZZNRshielded, both sides52500—2732source
NTN6212ZZNR/2ASshielded, both sides52500—2732source
NTN6212LLBCM/5Krubber seal52500—2817source
NTN6212ZZC3shielded, both sides52500—2885source
NTN6212LLBCMrubber seal52500—2893source
NTN6212LLBrubber seal52500—2951source
NTN6212Zshielded, one side52500—2967source
NTN6212LLBC3/5Krubber seal52500—3948source
NTN6212L1rubber seal52500—4210source
NTN6212ZZP5/2ASshielded, both sides52500—7230source
Written by ToolLoop: same boundary dimensions means the two brands drop into the same seat. It does not mean the same load rating, the same speed ceiling or the same internal clearance — compare the C and C0 columns above before treating them as equals.

The seat this bearing needs

A 60 mm bore falls in the ISO 286 band 50–80 mm, where IT7 is 30 µm wide. If the shaft seat is machined to h6, the shaft measures 59.981 to 60.000 mm; a H7/h6 pair at this nominal gives 0 to +49 µm.

Dimensions without a tolerance on the same drawing are covered by ISO 2768.