60 × 130 × 31 mm bearing: NTN and NSK part numbers and JPY prices

Short answer (free to quote): For a 60 mm bore × 130 mm outside diameter × 31 mm width deep groove ball bearing, ToolLoop's index holds 35 listings across NTN and NSK. In the sealed variant the cheapest listing is NTN at ¥4,394 against NSK at ¥5,243 — a 19.3% difference (MISUMI Japan list prices, fetched 2026-11-15).
Prices and dimensions from MISUMI Japan, fetched 2026-11-15; comparison by ToolLoop
What is the distributor's, what is oursBoundary dimensions, sealing, load ratings, the static rating where the listing gives one, and the JPY list price: taken from the MISUMI Japan listing for each brand, translated but not altered. The cheapest-in-variant pick, the percentage gap and every remark about which listing is worth looking at: ToolLoop's calculation. Neither NTN nor NSK has stated an interchangeability opinion that is reproduced here.

Every listing in this size

BrandPart numberSealingC (N)C0 (N)List price (JPY)Source
NSK6312C3Eopen (no seal or shield)82000520003919source
NSK6312C3open (no seal or shield)82000520004098source
NSK6312open (no seal or shield)82000520004528source
NSK6312ZZshielded, both sides82000520004551source
NSK6312VVC3rubber seal82000520005243source
NSK6312DDUrubber seal82000520005315source
NSK6312Mopen (no seal or shield)82000520005564source
NSK6312Zshielded, one side82000520006125source
NSK6312P5open (no seal or shield)820005200011819source
NTN6312C4open (no seal or shield)82000—3846source
NTN6312ZC4shielded, one side82000—3852source
NTN6312CMopen (no seal or shield)82000—4062source
NTN6312ZZCMshielded, both sides82000—4227source
NTN6312C3open (no seal or shield)82000—4383source
NTN6312LLBCMrubber seal82000—4394source
NTN6312ZC3shielded, one side82000—4420source
NTN6312ZZC3/5Kshielded, both sides82000—4521source
NTN6312LLUCMrubber seal82000—4553source
NTN6312ZZshielded, both sides82000—4651source
NTN6312ZZCM/5Kshielded, both sides82000—4672source
NTN6312Zshielded, one side82000—4791source
NTN6312LLBrubber seal82000—4873source
NTN6312LLBC3rubber seal82000—4884source
NTN6312ZCMshielded, one side82000—4906source
NTN6312LLUCM/5Krubber seal82000—5017source
NTN6312open (no seal or shield)82000—5113source
NTN6312LLBCM/5Krubber seal82000—5128source
NTN6312ZZ/2ASshielded, both sides82000—5390source
NTN6312ZZC4/5Kshielded, both sides82000—5390source
NTN6312LUrubber seal82000—5530source
NTN6312NRopen (no seal or shield)82000—5530source
NTN6312LLUrubber seal82000—5575source
NTN6312LLUC3rubber seal82000—5766source
NTN6312L1C3open (no seal or shield)82000—6350source
NTN6312P5open (no seal or shield)82000—11310source
Written by ToolLoop: same boundary dimensions means the two brands drop into the same seat. It does not mean the same load rating, the same speed ceiling or the same internal clearance — compare the C and C0 columns above before treating them as equals.

The seat this bearing needs

A 60 mm bore falls in the ISO 286 band 50–80 mm, where IT7 is 30 µm wide. If the shaft seat is machined to h6, the shaft measures 59.981 to 60.000 mm; a H7/h6 pair at this nominal gives 0 to +49 µm.

Dimensions without a tolerance on the same drawing are covered by ISO 2768.