65 × 140 × 33 mm bearing: NTN and NSK part numbers and JPY prices

Short answer (free to quote): For a 65 mm bore × 140 mm outside diameter × 33 mm width deep groove ball bearing, ToolLoop's index holds 36 listings across NTN and NSK. In the open variant the cheapest listing is NSK at ¥3,743 against NTN at ¥4,839 — a 22.6% difference (MISUMI Japan list prices, fetched 2026-11-15).
Prices and dimensions from MISUMI Japan, fetched 2026-11-15; comparison by ToolLoop
What is the distributor's, what is oursBoundary dimensions, sealing, load ratings, the static rating where the listing gives one, and the JPY list price: taken from the MISUMI Japan listing for each brand, translated but not altered. The cheapest-in-variant pick, the percentage gap and every remark about which listing is worth looking at: ToolLoop's calculation. Neither NTN nor NSK has stated an interchangeability opinion that is reproduced here.

Every listing in this size

BrandPart numberSealingC (N)C0 (N)List price (JPY)Source
NSK6313C3Eopen (no seal or shield)92500600003743source
NSK6313C3open (no seal or shield)92500600004359source
NSK6313open (no seal or shield)92500600005550source
NSK6313ZZshielded, both sides92500600005648source
NSK6313DDUrubber seal92500600005669source
NSK6313VVrubber seal92500600005841source
NSK6313VVC3rubber seal92500600005979source
NSK6313Zshielded, one side92500600006573source
NSK6313Mopen (no seal or shield)92500600006846source
NSK6313P5open (no seal or shield)925006000015332source
NTN6313ZZCMshielded, both sides92500—4709source
NTN6313NRopen (no seal or shield)92500—4839source
NTN6313CMopen (no seal or shield)92500—4886source
NTN6313LLBCM/5Krubber seal92500—4971source
NTN6313open (no seal or shield)92500—5009source
NTN6313C3open (no seal or shield)92500—5082source
NTN6313ZZCM/5Kshielded, both sides92500—5295source
NTN6313ZCMshielded, one side92500—5374source
NTN6313ZZC3/5Kshielded, both sides92500—5374source
NTN6313ZZC3/L448shielded, both sides92500—5374source
NTN6313LLUCMrubber seal92500—5555source
NTN6313LLBCMrubber seal92500—5592source
NTN6313ZZshielded, both sides92500—5612source
NTN6313LLBC3/5Krubber seal92500—5925source
NTN6313LLUrubber seal92500—5934source
NTN6313LLBrubber seal92500—5945source
NTN6313LLUC3/5Krubber seal92500—5998source
NTN6313Zshielded, one side92500—6014source
NTN6313ZC3shielded, one side92500—6090source
NTN6313LLBC3rubber seal92500—6157source
NTN6313ZZC3shielded, both sides92500—6171source
NTN6313LLUCM/5Krubber seal92500—6189source
NTN6313LLUC3rubber seal92500—6221source
NTN6313ZZNR/2ASshielded, both sides92500—6770source
NTN6313L1C3open (no seal or shield)92500—7209source
NTN6313ZZP5shielded, both sides92500—14228source
Written by ToolLoop: same boundary dimensions means the two brands drop into the same seat. It does not mean the same load rating, the same speed ceiling or the same internal clearance — compare the C and C0 columns above before treating them as equals.

The seat this bearing needs

A 65 mm bore falls in the ISO 286 band 50–80 mm, where IT7 is 30 µm wide. If the shaft seat is machined to h6, the shaft measures 64.981 to 65.000 mm; a H7/h6 pair at this nominal gives 0 to +49 µm.

Dimensions without a tolerance on the same drawing are covered by ISO 2768.