70 × 150 × 35 mm bearing: NTN and NSK part numbers and JPY prices

Short answer (free to quote): For a 70 mm bore × 150 mm outside diameter × 35 mm width deep groove ball bearing, ToolLoop's index holds 33 listings across NTN and NSK. In the shielded variant the cheapest listing is NTN at ¥5,239 against NSK at ¥6,345 — a 21.1% difference (MISUMI Japan list prices, fetched 2026-11-15).
Prices and dimensions from MISUMI Japan, fetched 2026-11-15; comparison by ToolLoop
What is the distributor's, what is oursBoundary dimensions, sealing, load ratings, the static rating where the listing gives one, and the JPY list price: taken from the MISUMI Japan listing for each brand, translated but not altered. The cheapest-in-variant pick, the percentage gap and every remark about which listing is worth looking at: ToolLoop's calculation. Neither NTN nor NSK has stated an interchangeability opinion that is reproduced here.

Every listing in this size

BrandPart numberSealingC (N)C0 (N)List price (JPY)Source
NSK6314C3Eopen (no seal or shield)104000680004493source
NSK6314C3open (no seal or shield)104000680006014source
NSK6314ZZC3shielded, both sides104000680006345source
NSK6314Zshielded, one side104000680006500source
NSK6314DDUrubber seal104000680006845source
NSK6314VVrubber seal104000680006953source
NSK6314NRopen (no seal or shield)104000680006997source
NSK6314open (no seal or shield)104000680007143source
NSK6314VVC3rubber seal104000680007477source
NSK6314Mopen (no seal or shield)104000680007742source
NTN6314ZZCMshielded, both sides104000—5239source
NTN6314C3open (no seal or shield)104000—5455source
NTN6314CMopen (no seal or shield)104000—5455source
NTN6314LLBCMrubber seal104000—5872source
NTN6314LLUCMrubber seal104000—5872source
NTN6314C4open (no seal or shield)104000—5980source
NTN6314open (no seal or shield)104000—6367source
NTN6314LLBCM/5Krubber seal104000—6431source
NTN6314LLUC3/5Krubber seal104000—6434source
NTN6314LLUC3rubber seal104000—6443source
NTN6314LLUCM/5Krubber seal104000—6466source
NTN6314ZC3shielded, one side104000—6516source
NTN6314ZCMshielded, one side104000—6516source
NTN6314LLBC3rubber seal104000—6528source
NTN6314ZZCM/5Kshielded, both sides104000—6810source
NTN6314ZZshielded, both sides104000—6843source
NTN6314ZZC3shielded, both sides104000—7034source
NTN6314Zshielded, one side104000—7327source
NTN6314LLBC3/5Krubber seal104000—7335source
NTN6314LLBrubber seal104000—7342source
NTN6314LLUrubber seal104000—7343source
NTN6314ZZC4/5Kshielded, both sides104000—7448source
NTN6314L1C3open (no seal or shield)104000—7980source
Written by ToolLoop: same boundary dimensions means the two brands drop into the same seat. It does not mean the same load rating, the same speed ceiling or the same internal clearance — compare the C and C0 columns above before treating them as equals.

The seat this bearing needs

A 70 mm bore falls in the ISO 286 band 50–80 mm, where IT7 is 30 µm wide. If the shaft seat is machined to h6, the shaft measures 69.981 to 70.000 mm; a H7/h6 pair at this nominal gives 0 to +49 µm.

Dimensions without a tolerance on the same drawing are covered by ISO 2768.