80 × 140 × 26 mm bearing: NTN and NSK part numbers and JPY prices

Short answer (free to quote): For a 80 mm bore × 140 mm outside diameter × 26 mm width deep groove ball bearing, ToolLoop's index holds 35 listings across NTN and NSK. In the sealed variant the cheapest listing is NTN at ¥3,948 against NSK at ¥4,463 — a 13.0% difference (MISUMI Japan list prices, fetched 2026-11-15).
Prices and dimensions from MISUMI Japan, fetched 2026-11-15; comparison by ToolLoop
What is the distributor's, what is oursBoundary dimensions, sealing, load ratings, the static rating where the listing gives one, and the JPY list price: taken from the MISUMI Japan listing for each brand, translated but not altered. The cheapest-in-variant pick, the percentage gap and every remark about which listing is worth looking at: ToolLoop's calculation. Neither NTN nor NSK has stated an interchangeability opinion that is reproduced here.

Every listing in this size

BrandPart numberSealingC (N)C0 (N)List price (JPY)Source
NSK6216C3Eopen (no seal or shield)72500530003355source
NSK6216C4open (no seal or shield)72500530003648source
NSK6216open (no seal or shield)72500530004104source
NSK6216Zshielded, one side72500530004245source
NSK6216VVrubber seal72500530004463source
NSK6216ZZshielded, both sides72500530004543source
NSK6216DDUrubber seal72500530004763source
NSK6216Mopen (no seal or shield)72500530005199source
NSK6216MC3open (no seal or shield)72500530005282source
NSK6216P5open (no seal or shield)725005300010961source
NTN6216open (no seal or shield)72500—3497source
NTN6216C3open (no seal or shield)72500—3705source
NTN6216CMopen (no seal or shield)72500—3764source
NTN6216ZZshielded, both sides72500—3898source
NTN6216LLBCMrubber seal72500—3948source
NTN6216ZZC3shielded, both sides72500—4080source
NTN6216LLUCMrubber seal72500—4155source
NTN6216LLBCM/5Krubber seal72500—4215source
NTN6216ZC3shielded, one side72500—4328source
NTN6216ZZC3/5Kshielded, both sides72500—4328source
NTN6216LLUC3rubber seal72500—4499source
NTN6216NRopen (no seal or shield)72500—4518source
NTN6216ZZCM/5Kshielded, both sides72500—4573source
NTN6216LLUCM/5Krubber seal72500—4883source
NTN6216C4open (no seal or shield)72500—4930source
NTN6216LLUC3/5Krubber seal72500—5223source
NTN6216LLBrubber seal72500—5237source
NTN6216Zshielded, one side72500—5330source
NTN6216ZCMshielded, one side72500—5366source
NTN6216NXRopen (no seal or shield)72500—5470source
NTN6216LLUrubber seal72500—5556source
NTN6216ZNRshielded, one side72500—5560source
NTN6216LLBC3rubber seal72500—5885source
NTN6216L1C3rubber seal72500—5980source
NTN6216LLBC3/5Krubber seal72500—6280source
Written by ToolLoop: same boundary dimensions means the two brands drop into the same seat. It does not mean the same load rating, the same speed ceiling or the same internal clearance — compare the C and C0 columns above before treating them as equals.

The seat this bearing needs

A 80 mm bore falls in the ISO 286 band 50–80 mm, where IT7 is 30 µm wide. If the shaft seat is machined to h6, the shaft measures 79.981 to 80.000 mm; a H7/h6 pair at this nominal gives 0 to +49 µm.

Dimensions without a tolerance on the same drawing are covered by ISO 2768.