12 × 32 × 10 mm bearing: NTN and NSK part numbers and JPY prices

Short answer (free to quote): For a 12 mm bore × 32 mm outside diameter × 10 mm width deep groove ball bearing, ToolLoop's index holds 50 listings across NTN and NSK. In the open variant the cheapest listing is NSK at ¥256 against NTN at ¥339 — a 24.5% difference (MISUMI Japan list prices, fetched 2026-11-15).
Prices and dimensions from MISUMI Japan, fetched 2026-11-15; comparison by ToolLoop
What is the distributor's, what is oursBoundary dimensions, sealing, load ratings, the static rating where the listing gives one, and the JPY list price: taken from the MISUMI Japan listing for each brand, translated but not altered. The cheapest-in-variant pick, the percentage gap and every remark about which listing is worth looking at: ToolLoop's calculation. Neither NTN nor NSK has stated an interchangeability opinion that is reproduced here.

Every listing in this size

BrandPart numberSealingC (N)C0 (N)List price (JPY)Source
NSK6201C3Eopen (no seal or shield)68003050256source
NSK6201ZZC3shielded, both sides68003050339source
NSK6201ZZshielded, both sides68003050357source
NSK6201open (no seal or shield)68003050359source
NSK6201DDUNRrubber seal68003050383source
NSK6201NRopen (no seal or shield)68003050384source
NSK6201DDUrubber seal68003050399source
NSK6201VVrubber seal68003050399source
NSK6201ZZNRshielded, both sides68003050405source
NSK6201Zshielded, one side68003050413source
NSK6201DDUC3E NS7S1rubber seal68003050470source
NSK6201-H-20T1XZZshielded, both sides68003050782source
NSK6201U-H-20T1Xopen (no seal or shield)680030501064source
NSK6201L11DDUrubber seal680030501080source
NSK6201-H-ZZU76UG22shielded, both sides680030501924source
NTN6201CMopen (no seal or shield)6100—339source
NTN6201ZZshielded, both sides6100—343source
NTN6201ZZC3/5Kshielded, both sides6100—358source
NTN6201ZZCM/5Kshielded, both sides6100—393source
NTN6201ZZNRshielded, both sides6100—395source
NTN6201LLBCMrubber seal6100—412source
NTN6201LLU/2ASrubber seal6100—414source
NTN6201LLUCM/5Krubber seal6100—423source
NTN6201LLBCM/5Krubber seal6100—439source
NTN6201ZCMshielded, one side6100—443source
NTN6201open (no seal or shield)6100—454source
NTN6201LLUrubber seal6100—473source
NTN6201ZZC4shielded, both sides6100—473source
NTN6201C3open (no seal or shield)6100—513source
NTN6201ZZC4/5Kshielded, both sides6100—525source
NTN6201ZZCMshielded, both sides6100—537source
NTN6201Zshielded, one side6100—540source
NTN6201ZZNR/2ASshielded, both sides6100—547source
NTN6201LLBC3rubber seal6100—596source
NTN6201LBrubber seal6100—604source
NTN6201LUrubber seal6100—627source
NTN6201LLUC3rubber seal6100—628source
NTN6201LLUCMrubber seal6100—628source
NTN6201ZZC3shielded, both sides6100—633source
NTN6201LLUC3/5Krubber seal6100—649source
NTN6201LLBC3/5Krubber seal6100—667source
NTN6201LLBrubber seal6100—680source
NTN6201ZNRshielded, one side6100—784source
NTN6201ZC3shielded, one side6100—790source
NTN6201NRopen (no seal or shield)6100—800source
NTN6201ZZNRC3/5Kshielded, both sides6100—830source
NTN6201LLBNR/2ASrubber seal6100—860source
NTN6201LLUNR/2ASrubber seal6100—860source
NTN6201ZZ/LP03shielded, both sides6100—860source
NTN6201LLU/LP03rubber seal6100—900source
Written by ToolLoop: same boundary dimensions means the two brands drop into the same seat. It does not mean the same load rating, the same speed ceiling or the same internal clearance — compare the C and C0 columns above before treating them as equals.

The seat this bearing needs

A 12 mm bore falls in the ISO 286 band 10–18 mm, where IT7 is 18 µm wide. If the shaft seat is machined to h6, the shaft measures 11.989 to 12.000 mm; a H7/h6 pair at this nominal gives 0 to +29 µm.

Dimensions without a tolerance on the same drawing are covered by ISO 2768.