17 × 35 × 10 mm bearing: NTN and NSK part numbers and JPY prices

Short answer (free to quote): For a 17 mm bore × 35 mm outside diameter × 10 mm width deep groove ball bearing, ToolLoop's index holds 51 listings across NTN and NSK. In the shielded variant the cheapest listing is NSK at ¥439 against NTN at ¥498 — a 11.8% difference (MISUMI Japan list prices, fetched 2026-11-15).
Prices and dimensions from MISUMI Japan, fetched 2026-11-15; comparison by ToolLoop
What is the distributor's, what is oursBoundary dimensions, sealing, load ratings, the static rating where the listing gives one, and the JPY list price: taken from the MISUMI Japan listing for each brand, translated but not altered. The cheapest-in-variant pick, the percentage gap and every remark about which listing is worth looking at: ToolLoop's calculation. Neither NTN nor NSK has stated an interchangeability opinion that is reproduced here.

Every listing in this size

BrandPart numberSealingC (N)C0 (N)List price (JPY)Source
NSK6003NRopen (no seal or shield)60003250320source
NSK6003C3Eopen (no seal or shield)60003250356source
NSK6003DUrubber seal60003250408source
NSK6003DDUC3rubber seal60003250424source
NSK6003DDUC3Erubber seal60003250424source
NSK6003ZZshielded, both sides60003250439source
NSK6003ZZC3shielded, both sides60003250458source
NSK6003open (no seal or shield)60003250467source
NSK6003VVrubber seal60003250516source
NSK6003ZZNRshielded, both sides60003250518source
NSK6003Zshielded, one side60003250533source
NSK6003DDUrubber seal60003250567source
NSK6003-H-20T1XZZshielded, both sides600032501046source
NSK6003L11DDUrubber seal600032501080source
NSK6003-H-20T1XDDUrubber seal600032501160source
NSK6003-H-ZZU76UG22shielded, both sides600032502217source
NSK6003L11-H-20DDUrubber seal600032504150source
NTN6003CMopen (no seal or shield)6800—319source
NTN6003LLUC3/5Krubber seal6800—425source
NTN6003LLBrubber seal6800—458source
NTN6003Zshielded, one side6800—498source
NTN6003ZZNR/2ASshielded, both sides6800—505source
NTN6003ZZNRshielded, both sides6800—506source
NTN6003ZZC3shielded, both sides6800—517source
NTN6003LLUrubber seal6800—552source
NTN6003ZC3shielded, one side6800—558source
NTN6003open (no seal or shield)6800—582source
NTN6003C3open (no seal or shield)6800—608source
NTN6003LLUCMrubber seal6800—630source
NTN6003ZZshielded, both sides6800—633source
NTN6003LLBC3rubber seal6800—644source
NTN6003LLBCM/5Krubber seal6800—644source
NTN6003LLBCMrubber seal6800—676source
NTN6003LLU/LP03rubber seal6800—722source
NTN6003LLB/LP03rubber seal6800—723source
NTN6003LLUNRrubber seal6800—732source
NTN6003ZCMshielded, one side6800—734source
NTN6003LLUCM/5Krubber seal6800—747source
NTN6003ZZC3/5Kshielded, both sides6800—767source
NTN6003LLUC3rubber seal6800—783source
NTN6003LLBC3/5Krubber seal6800—793source
NTN6003LUrubber seal6800—798source
NTN6003ZZC4/5Kshielded, both sides6800—860source
NTN6003ZNRshielded, one side6800—910source
NTN6003ZZ/LP03shielded, both sides6800—940source
NTN6003LLBNR/2ASrubber seal6800—950source
NTN6003LLUNR/2ASrubber seal6800—950source
NTN6003LLUP5/2ASrubber seal6800—1480source
NTN6003LLBP5/2ASrubber seal6800—1488source
NTN6003LLBP5rubber seal6800—1555source
NTN6003P5open (no seal or shield)6800—2034source
Written by ToolLoop: same boundary dimensions means the two brands drop into the same seat. It does not mean the same load rating, the same speed ceiling or the same internal clearance — compare the C and C0 columns above before treating them as equals.

The seat this bearing needs

A 17 mm bore falls in the ISO 286 band 10–18 mm, where IT7 is 18 µm wide. If the shaft seat is machined to h6, the shaft measures 16.989 to 17.000 mm; a H7/h6 pair at this nominal gives 0 to +29 µm.

Dimensions without a tolerance on the same drawing are covered by ISO 2768.