17 × 40 × 12 mm bearing: NTN and NSK part numbers and JPY prices

Short answer (free to quote): For a 17 mm bore × 40 mm outside diameter × 12 mm width deep groove ball bearing, ToolLoop's index holds 55 listings across NTN and NSK. In the sealed variant the cheapest listing is NSK at ¥444 against NTN at ¥707 — a 37.2% difference (MISUMI Japan list prices, fetched 2026-11-15).
Prices and dimensions from MISUMI Japan, fetched 2026-11-15; comparison by ToolLoop
What is the distributor's, what is oursBoundary dimensions, sealing, load ratings, the static rating where the listing gives one, and the JPY list price: taken from the MISUMI Japan listing for each brand, translated but not altered. The cheapest-in-variant pick, the percentage gap and every remark about which listing is worth looking at: ToolLoop's calculation. Neither NTN nor NSK has stated an interchangeability opinion that is reproduced here.

Every listing in this size

BrandPart numberSealingC (N)C0 (N)List price (JPY)Source
NSK6203C3Eopen (no seal or shield)95504800343source
NSK6203C3open (no seal or shield)95504800345source
NSK6203DDUNRrubber seal95504800444source
NSK6203ZZshielded, both sides95504800456source
NSK6203ZZC3shielded, both sides95504800456source
NSK6203open (no seal or shield)95504800467source
NSK6203DDUrubber seal95504800497source
NSK6203VVrubber seal95504800497source
NSK6203VVC3rubber seal95504800517source
NSK6203ZZNRshielded, both sides95504800518source
NSK6203Zshielded, one side95504800533source
NSK6203-H-20T1XDDUrubber seal955048001331source
NSK6203L11DDUrubber seal955048001578source
NSK6203-H-ZZU76UG1shielded, both sides955048002481source
NSK6203L11-H-20DDUrubber seal955048006099source
NTN6203C3open (no seal or shield)9600—424source
NTN6203C4open (no seal or shield)9600—443source
NTN6203ZZshielded, both sides9600—454source
NTN6203ZZCMshielded, both sides9600—480source
NTN6203ZZCM/5Kshielded, both sides9600—497source
NTN6203ZCMshielded, one side9600—552source
NTN6203ZZNRC3shielded, both sides9600—571source
NTN6203ZZCM/L448shielded, both sides9600—577source
NTN6203open (no seal or shield)9600—582source
NTN6203CMopen (no seal or shield)9600—607source
NTN6203ZZNRshielded, both sides9600—629source
NTN6203ZZC3/5Kshielded, both sides9600—676source
NTN6203ZNRshielded, one side9600—684source
NTN6203Zshielded, one side9600—692source
NTN6203LLUCM/5Krubber seal9600—707source
NTN6203ZZC3shielded, both sides9600—712source
NTN6203LLBC3rubber seal9600—715source
NTN6203LBrubber seal9600—728source
NTN6203LLUC3rubber seal9600—728source
NTN6203LLUC3/5Krubber seal9600—729source
NTN6203LLUNR/2ASrubber seal9600—729source
NTN6203LLBCMrubber seal9600—741source
NTN6203LLBCM/5Krubber seal9600—747source
NTN6203LLUrubber seal9600—748source
NTN6203ZZNRC3/2ASshielded, both sides9600—757source
NTN6203LLUCMrubber seal9600—758source
NTN6203LLBrubber seal9600—771source
NTN6203LUrubber seal9600—798source
NTN6203LLUNRrubber seal9600—800source
NTN6203LLBC3/5Krubber seal9600—829source
NTN6203ZC3shielded, one side9600—860source
NTN6203ZZC3/L448shielded, both sides9600—860source
NTN6203ZZC4/5Kshielded, both sides9600—860source
NTN6203NRopen (no seal or shield)9600—870source
NTN6203ZZ/LP03shielded, both sides9600—940source
NTN6203L1C3rubber seal9600—950source
NTN6203LLB/LP03rubber seal9600—1000source
NTN6203LLU/LP03rubber seal9600—1000source
NTN6203ZZP5/2ASshielded, both sides9600—1240source
NTN6203ZZP5shielded, both sides9600—1247source
Written by ToolLoop: same boundary dimensions means the two brands drop into the same seat. It does not mean the same load rating, the same speed ceiling or the same internal clearance — compare the C and C0 columns above before treating them as equals.

The seat this bearing needs

A 17 mm bore falls in the ISO 286 band 10–18 mm, where IT7 is 18 µm wide. If the shaft seat is machined to h6, the shaft measures 16.989 to 17.000 mm; a H7/h6 pair at this nominal gives 0 to +29 µm.

Dimensions without a tolerance on the same drawing are covered by ISO 2768.