25 × 47 × 12 mm bearing: NTN and NSK part numbers and JPY prices

Short answer (free to quote): For a 25 mm bore × 47 mm outside diameter × 12 mm width deep groove ball bearing, ToolLoop's index holds 50 listings across NTN and NSK. In the open variant the cheapest listing is NSK at ¥444 against NTN at ¥513 — a 13.5% difference (MISUMI Japan list prices, fetched 2026-11-15).
Prices and dimensions from MISUMI Japan, fetched 2026-11-15; comparison by ToolLoop
What is the distributor's, what is oursBoundary dimensions, sealing, load ratings, the static rating where the listing gives one, and the JPY list price: taken from the MISUMI Japan listing for each brand, translated but not altered. The cheapest-in-variant pick, the percentage gap and every remark about which listing is worth looking at: ToolLoop's calculation. Neither NTN nor NSK has stated an interchangeability opinion that is reproduced here.

Every listing in this size

BrandPart numberSealingC (N)C0 (N)List price (JPY)Source
NSK6005C3Eopen (no seal or shield)101005850444source
NSK6005NRopen (no seal or shield)101005850526source
NSK6005ZZC3shielded, both sides101005850561source
NSK6005ZZshielded, both sides101005850564source
NSK6005VVC3Erubber seal101005850568source
NSK6005open (no seal or shield)101005850571source
NSK6005DUCMrubber seal101005850601source
NSK6005ZZNRshielded, both sides101005850655source
NSK6005VVrubber seal101005850657source
NSK6005Zshielded, one side101005850659source
NSK6005DDUrubber seal101005850722source
NSK6005-H-20T1XBZZshielded, both sides1010058501396source
NSK6005-H-20T1XBDDUrubber seal1010058501423source
NSK6005U-H-20T1XBopen (no seal or shield)1010058501475source
NSK6005P5open (no seal or shield)1010058501616source
NTN6005open (no seal or shield)10100—513source
NTN6005ZZCM/5Kshielded, both sides10100—567source
NTN6005LLBCMrubber seal10100—576source
NTN6005ZZCMshielded, both sides10100—591source
NTN6005LLBCM/5Krubber seal10100—611source
NTN6005LLUCM/5Krubber seal10100—628source
NTN6005ZZshielded, both sides10100—636source
NTN6005CMopen (no seal or shield)10100—643source
NTN6005LLUC3/5Krubber seal10100—663source
NTN6005LLBrubber seal10100—688source
NTN6005LLUrubber seal10100—688source
NTN6005ZZC3shielded, both sides10100—690source
NTN6005ZZNRshielded, both sides10100—690source
NTN6005ZNRshielded, one side10100—724source
NTN6005Zshielded, one side10100—733source
NTN6005C3open (no seal or shield)10100—739source
NTN6005LLUCMrubber seal10100—749source
NTN6005ZCMshielded, one side10100—764source
NTN6005ZZNR/2ASshielded, both sides10100—768source
NTN6005NRopen (no seal or shield)10100—809source
NTN6005LLUNRrubber seal10100—819source
NTN6005LLU/LP03rubber seal10100—865source
NTN6005LLUNR/2ASrubber seal10100—877source
NTN6005LLBC3/5Krubber seal10100—881source
NTN6005LLBC3rubber seal10100—890source
NTN6005LUrubber seal10100—914source
NTN6005ZC3shielded, one side10100—930source
NTN6005ZZC4/5Kshielded, both sides10100—930source
NTN6005ZZC3/5Kshielded, both sides10100—948source
NTN6005LLUC3rubber seal10100—949source
NTN6005ZZNRC3/2ASshielded, both sides10100—990source
NTN6005ZZ/LP03shielded, both sides10100—1030source
NTN6005LLB/LP03rubber seal10100—1100source
NTN6005LLUP5/2ASrubber seal10100—1710source
NTNSSN005LL/LP03rubber seal7750—4948source
Written by ToolLoop: same boundary dimensions means the two brands drop into the same seat. It does not mean the same load rating, the same speed ceiling or the same internal clearance — compare the C and C0 columns above before treating them as equals.

The seat this bearing needs

A 25 mm bore falls in the ISO 286 band 18–30 mm, where IT7 is 21 µm wide. If the shaft seat is machined to h6, the shaft measures 24.987 to 25.000 mm; a H7/h6 pair at this nominal gives 0 to +34 µm.

Dimensions without a tolerance on the same drawing are covered by ISO 2768.