35 × 62 × 14 mm bearing: NTN and NSK part numbers and JPY prices

Short answer (free to quote): For a 35 mm bore × 62 mm outside diameter × 14 mm width deep groove ball bearing, ToolLoop's index holds 48 listings across NTN and NSK. In the open variant the cheapest listing is NSK at ¥728 against NTN at ¥844 — a 13.7% difference (MISUMI Japan list prices, fetched 2026-11-15).
Prices and dimensions from MISUMI Japan, fetched 2026-11-15; comparison by ToolLoop
What is the distributor's, what is oursBoundary dimensions, sealing, load ratings, the static rating where the listing gives one, and the JPY list price: taken from the MISUMI Japan listing for each brand, translated but not altered. The cheapest-in-variant pick, the percentage gap and every remark about which listing is worth looking at: ToolLoop's calculation. Neither NTN nor NSK has stated an interchangeability opinion that is reproduced here.

Every listing in this size

BrandPart numberSealingC (N)C0 (N)List price (JPY)Source
NSK6007ZZC3Eshielded, both sides1600010300618source
NSK6007NRopen (no seal or shield)1600010300728source
NSK6007ZZshielded, both sides1600010300769source
NSK6007ZZC3shielded, both sides1600010300776source
NSK6007VVC3Erubber seal1600010300816source
NSK6007DUCMrubber seal1600010300844source
NSK6007open (no seal or shield)1600010300849source
NSK6007DDUrubber seal1600010300938source
NSK6007VVrubber seal1600010300938source
NSK6007ZZNRshielded, both sides1600010300960source
NSK6007Zshielded, one side1600010300977source
NSK6007-H-20T1XDDUrubber seal16000103003598source
NSK6007U-H-20T1Xopen (no seal or shield)16000103004167source
NTN6007ZCMshielded, one side16000—707source
NTN6007ZZCMshielded, both sides16000—796source
NTN6007ZZC3shielded, both sides16000—831source
NTN6007CMopen (no seal or shield)16000—844source
NTN6007NRopen (no seal or shield)16000—860source
NTN6007ZC3shielded, one side16000—869source
NTN6007LLBCMrubber seal16000—896source
NTN6007ZZCM/5Kshielded, both sides16000—898source
NTN6007ZZshielded, both sides16000—901source
NTN6007Zshielded, one side16000—902source
NTN6007LUrubber seal16000—914source
NTN6007ZZC3/5Kshielded, both sides16000—935source
NTN6007LLBCM/5Krubber seal16000—942source
NTN6007LLUCM/5Krubber seal16000—962source
NTN6007LLUCMrubber seal16000—1011source
NTN6007LLBrubber seal16000—1018source
NTN6007LLUrubber seal16000—1018source
NTN6007LLBNR/2ASrubber seal16000—1023source
NTN6007U1open (no seal or shield)16000—1030source
NTN6007ZZNR/2ASshielded, both sides16000—1032source
NTN6007LLBNRrubber seal16000—1034source
NTN6007C3open (no seal or shield)16000—1048source
NTN6007LBrubber seal16000—1081source
NTN6007ZZNRshielded, both sides16000—1094source
NTN6007ZZC4/5Kshielded, both sides16000—1100source
NTN6007LLBC3rubber seal16000—1123source
NTN6007LLUC3/5Krubber seal16000—1212source
NTN6007LLBC3/5Krubber seal16000—1246source
NTN6007LLUNR/2ASrubber seal16000—1260source
NTN6007ZZ/LP03shielded, both sides16000—1260source
NTN6007LLU/LP03rubber seal16000—1350source
NTN6007ZZP5/2ASshielded, both sides16000—2160source
NTN6007LLBP5/2ASrubber seal16000—2240source
NTN6007P5open (no seal or shield)16000—3619source
NTN6007P4open (no seal or shield)16000—4341source
Written by ToolLoop: same boundary dimensions means the two brands drop into the same seat. It does not mean the same load rating, the same speed ceiling or the same internal clearance — compare the C and C0 columns above before treating them as equals.

The seat this bearing needs

A 35 mm bore falls in the ISO 286 band 30–50 mm, where IT7 is 25 µm wide. If the shaft seat is machined to h6, the shaft measures 34.984 to 35.000 mm; a H7/h6 pair at this nominal gives 0 to +41 µm.

Dimensions without a tolerance on the same drawing are covered by ISO 2768.