12 × 28 × 8 mm bearing: NTN and NSK part numbers and JPY prices

Short answer (free to quote): For a 12 mm bore × 28 mm outside diameter × 8 mm width deep groove ball bearing, ToolLoop's index holds 58 listings across NTN and NSK. In the open variant the cheapest listing is NTN at ¥348 against NSK at ¥407 — a 17.0% difference (MISUMI Japan list prices, fetched 2026-11-15).
Prices and dimensions from MISUMI Japan, fetched 2026-11-15; comparison by ToolLoop
What is the distributor's, what is oursBoundary dimensions, sealing, load ratings, the static rating where the listing gives one, and the JPY list price: taken from the MISUMI Japan listing for each brand, translated but not altered. The cheapest-in-variant pick, the percentage gap and every remark about which listing is worth looking at: ToolLoop's calculation. Neither NTN nor NSK has stated an interchangeability opinion that is reproduced here.

Every listing in this size

BrandPart numberSealingC (N)C0 (N)List price (JPY)Source
NSK6001ZCMshielded, one side51002370376source
NSK6001ZZshielded, both sides51002370387source
NSK6001VVC3Erubber seal51002370396source
NSK6001ZZC3shielded, both sides51002370406source
NSK6001open (no seal or shield)51002370407source
NSK6001C3Eopen (no seal or shield)51002370411source
NSK6001VVrubber seal51002370455source
NSK6001Zshielded, one side51002370466source
NSK6001ZZNRshielded, both sides51002370475source
NSK6001DDUrubber seal51002370500source
NSK6001CMopen (no seal or shield)51002370555source
NSK6001U-H-20T1Xopen (no seal or shield)51002370651source
NSK6001-H-20T1XZZshielded, both sides51002370766source
NSK6001-H-20T1XDDrubber seal51002370780source
NSK6001-H-20T1XDDUrubber seal51002370868source
NSK6001L11DDUrubber seal510023701021source
NSK6001ZZP5shielded, both sides510023701461source
NSK6001-H-ZZU76UG38shielded, both sides510023701595source
NSK6001L11-H-20DDUrubber seal510023702354source
NTN6001CMopen (no seal or shield)5100—348source
NTN6001ZZshielded, both sides5100—441source
NTN6001LLUCMrubber seal5100—454source
NTN6001JRXLLUCMrubber seal5100—465source
NTN6001LLBCMrubber seal5100—465source
NTN6001JRXCMopen (no seal or shield)5100—472source
NTN6001JRXLLUCM/5Krubber seal5100—484source
NTN6001JRXZshielded, one side5100—484source
NTN6001LLUrubber seal5100—485source
NTN6001ZCMshielded, one side5100—494source
NTN6001open (no seal or shield)5100—505source
NTN6001C3open (no seal or shield)5100—508source
NTN6001ZZNXRX/2ASshielded, both sides5100—549source
NTN6001JRXZCMshielded, one side5100—559source
NTN6001ZZCMshielded, both sides5100—568source
NTN6001ZZCM/5Kshielded, both sides5100—568source
NTN6001JRXLUrubber seal5100—583source
NTN6001JRXZZCMshielded, both sides5100—585source
NTN6001JRXZZCM/5Kshielded, both sides5100—595source
NTN6001JRXLLUC3rubber seal5100—596source
NTN6001JRXLLBCM/5Krubber seal5100—600source
NTN6001Zshielded, one side5100—607source
NTN6001LLBC3rubber seal5100—608source
NTN6001JRXZZNX2RX3/2ASshielded, both sides5100—609source
NTN6001JRXLLBCMrubber seal5100—623source
NTN6001LLBrubber seal5100—628source
NTN6001ZZC3shielded, both sides5100—649source
NTN6001JRXLLBC3rubber seal5100—654source
NTN6001LLB/LP03rubber seal5100—677source
NTN6001JRXLBrubber seal5100—685source
NTN6001JRXLLUC3/5Krubber seal5100—695source
NTN6001LUrubber seal5100—695source
NTN6001JRXLLBC3/5Krubber seal5100—713source
NTN6001JRXLLB/LP03rubber seal5100—727source
NTN6001JRXZC3shielded, one side5100—820source
NTN6001JRXZZ/LP03shielded, both sides5100—900source
NTN6001JRXLLU/LP03rubber seal5100—940source
NTN6001JRXZZP5/2ASshielded, both sides5100—1330source
NTN6001JRXLLBP5/2ASrubber seal5100—1360source
Written by ToolLoop: same boundary dimensions means the two brands drop into the same seat. It does not mean the same load rating, the same speed ceiling or the same internal clearance — compare the C and C0 columns above before treating them as equals.

The seat this bearing needs

A 12 mm bore falls in the ISO 286 band 10–18 mm, where IT7 is 18 µm wide. If the shaft seat is machined to h6, the shaft measures 11.989 to 12.000 mm; a H7/h6 pair at this nominal gives 0 to +29 µm.

Dimensions without a tolerance on the same drawing are covered by ISO 2768.