ISO 286 tolerances for 0–3 mm: IT grades and fit limits

Short answer (free to quote): In the 0–3 mm band of ISO 286-1, IT7 is 10 µm wide and IT6 is 6 µm, so an H7/h6 pair at a nominal 1.5 mm can move between 0 and +16 µm (calculated by ToolLoop, checked 2026-11-15). There are 36 deep groove ball bearing listings in ToolLoop's index with a bore in this band.
ISO 286-1:2010 tables; counts from the MISUMI Japan listing, fetched 2026-11-15
What is standard text, what is our arithmeticThe tolerance and deviation values are the tabulated values of ISO 286-1:2010 / ISO 2768-1:1989, taken from three independently published open datasets and compared cell by cell; only cells where all datasets that carry them agree are shown. The standard documents themselves are not reproduced. The limit sizes in millimetres, the clearance/interference ranges and every sentence about which fit is used for what are calculated or written by ToolLoop — they are not quoted from the standard.

Tolerance widths in this band

GradeWidth (µm)H hole EI/ES (µm)h shaft ei/es (µm)
IT540 / +4+4 / 0
IT660 / +6+6 / 0
IT7100 / +10+10 / 0
IT8140 / +14+14 / 0
IT9250 / +25+25 / 0
IT10400 / +40+40 / 0
IT11600 / +60+60 / 0

Fits in this band

FitHole EI/ESShaft ei/esClearance (µm)
H7/h60 / +10-6 / 00 … +16
H7/g60 / +10-8 / -2+2 … +18
H7/f70 / +10-16 / -6+6 … +26
H7/e80 / +10-28 / -14+14 … +38
H7/d90 / +10-45 / -20+20 … +55
H7/js60 / +10-3 / +3-3 … +13
H7/k60 / +100 / +6-6 … +10
H7/m60 / +10+2 / +8-8 … +8
H7/n60 / +10+4 / +10-10 … +6
H7/p60 / +10+6 / +12-12 … +4
H7/r60 / +10+10 / +16-16 … 0
H7/s60 / +10+14 / +20-20 … -4
H8/f70 / +14-16 / -6+6 … +30
H8/h70 / +14-10 / 00 … +24
H9/d90 / +25-45 / -20+20 … +70
H11/c110 / +60-120 / -60+60 … +180
Provenance: primary table ottonic/standards-mcp-server (src/domain/iso286.ts, MIT); cross-checked against clay-good/anvilate (tolerance/data/iso286_*.yaml, MIT) and chenzefeng09/iso-286-fits (fits.json, MIT). 393 overlapping cells compared, 0 disagreements, checked 2026-11-15.

Deep groove ball bearings with a bore in this band

36 listings; first 40 by bore.

Part numberBrandd × D × B (mm)SealingList price (JPY)
681-HNSK1 × 3 × 1open (no seal or shield)620
691-HNSK1 × 4 × 1.6open (no seal or shield)604
601XU-HNSK1.5 × 6 × 3open (no seal or shield)337
681X-H-ZZbrand not stated1.5 × 4 × 2shielded, both sides395
681XU-HNSK1.5 × 4 × 2open (no seal or shield)390
691X-H-ZZNSK1.5 × 5 × 2.6shielded, both sides418
691XU-HNSK1.5 × 5 × 2.6open (no seal or shield)405
F601X-H-ZZNSK1.5 × 6 × 3shielded, both sides495
F681X-H-ZZNSK1.5 × 4 × 2shielded, both sides439
F691X-H-ZZNSK1.5 × 5 × 2.6shielded, both sides622
682-H-ZZNSK2 × 5 × 2.3shielded, both sides387
682U-HNSK2 × 5 × 2.3open (no seal or shield)369
692-H-ZZNSK2 × 6 × 3shielded, both sides348
692U-HNSK2 × 6 × 3open (no seal or shield)394
F682-H-ZZNSK2 × 5 × 2.3shielded, both sides396
F682ZZNSK2 × 5 × 2.3shielded, both sides1040
F692-H-ZZNSK2 × 6 × 3shielded, both sides482
602X-H-ZZNSK2.5 × 8 × 4shielded, both sides433
602XU-HNSK2.5 × 8 × 4open (no seal or shield)321
682X-H-ZZNSK2.5 × 6 × 2.6shielded, both sides362
682XU-HNSK2.5 × 6 × 2.6open (no seal or shield)443
F602X-H-ZZNSK2.5 × 8 × 4shielded, both sides404
F682X-H-ZZbrand not stated2.5 × 6 × 2.6shielded, both sides421
F692X-H-ZZbrand not stated2.5 × 7 × 3.5shielded, both sides398
603U-HNSK3 × 9 × 5open (no seal or shield)479
623-H-DDNSK3 × 10 × 4rubber seal312
623-H-ZZU76UG7NSK3 × 10 × 4shielded, both sides741
623ZZNSK3 × 10 × 4shielded, both sides407
683U-HNSK3 × 7 × 3open (no seal or shield)320
693-H-ZZNSK3 × 8 × 4shielded, both sides279
693-H-ZZU76UG8NSK3 × 8 × 4shielded, both sides451
693U-HNSK3 × 8 × 4open (no seal or shield)364
F623ZZNSK3 × 11.5 × 4shielded, both sides401
F683ZZNSK3 × 8.1 × 3shielded, both sides339
F693ZZNSK3 × 8 × 4shielded, both sides387
MF63ZZNSK3 × 6 × 2.5shielded, both sides364