ISO 286 tolerances for 3–6 mm: IT grades and fit limits

Short answer (free to quote): In the 3–6 mm band of ISO 286-1, IT7 is 12 µm wide and IT6 is 8 µm, so an H7/h6 pair at a nominal 4.5 mm can move between 0 and +20 µm (calculated by ToolLoop, checked 2026-11-15). There are 86 deep groove ball bearing listings in ToolLoop's index with a bore in this band.
ISO 286-1:2010 tables; counts from the MISUMI Japan listing, fetched 2026-11-15
What is standard text, what is our arithmeticThe tolerance and deviation values are the tabulated values of ISO 286-1:2010 / ISO 2768-1:1989, taken from three independently published open datasets and compared cell by cell; only cells where all datasets that carry them agree are shown. The standard documents themselves are not reproduced. The limit sizes in millimetres, the clearance/interference ranges and every sentence about which fit is used for what are calculated or written by ToolLoop — they are not quoted from the standard.

Tolerance widths in this band

GradeWidth (µm)H hole EI/ES (µm)h shaft ei/es (µm)
IT550 / +5+5 / 0
IT680 / +8+8 / 0
IT7120 / +12+12 / 0
IT8180 / +18+18 / 0
IT9300 / +30+30 / 0
IT10480 / +48+48 / 0
IT11750 / +75+75 / 0

Fits in this band

FitHole EI/ESShaft ei/esClearance (µm)
H7/h60 / +12-8 / 00 … +20
H7/g60 / +12-12 / -4+4 … +24
H7/f70 / +12-22 / -10+10 … +34
H7/e80 / +12-38 / -20+20 … +50
H7/d90 / +12-60 / -30+30 … +72
H7/js60 / +12-4 / +4-4 … +16
H7/k60 / +12+1 / +9-9 … +11
H7/m60 / +12+4 / +12-12 … +8
H7/n60 / +12+8 / +16-16 … +4
H7/p60 / +12+12 / +20-20 … 0
H7/r60 / +12+15 / +23-23 … -3
H7/s60 / +12+19 / +27-27 … -7
H8/f70 / +18-22 / -10+10 … +40
H8/h70 / +18-12 / 00 … +30
H9/d90 / +30-60 / -30+30 … +90
H11/c110 / +75-145 / -70+70 … +220
Provenance: primary table ottonic/standards-mcp-server (src/domain/iso286.ts, MIT); cross-checked against clay-good/anvilate (tolerance/data/iso286_*.yaml, MIT) and chenzefeng09/iso-286-fits (fits.json, MIT). 393 overlapping cells compared, 0 disagreements, checked 2026-11-15.

Deep groove ball bearings with a bore in this band

86 listings; first 40 by bore.

Part numberBrandd × D × B (mm)SealingList price (JPY)
604-H-DDNSK4 × 12 × 4rubber seal357
604-H-ZZNSK4 × 12 × 4shielded, both sides294
604ZZNSK4 × 12 × 4shielded, both sides407
624-H-DDNSK4 × 13 × 5rubber seal389
624-H-ZZU76UG3NSK4 × 13 × 5shielded, both sides771
624U-HNSK4 × 13 × 5open (no seal or shield)378
624ZZNSK4 × 13 × 5shielded, both sides327
634U-HNSK4 × 16 × 5open (no seal or shield)378
684-H-ZZNSK4 × 9 × 4shielded, both sides290
684-H-ZZU76UG4NSK4 × 9 × 4shielded, both sides496
684U-HNSK4 × 9 × 4open (no seal or shield)378
694-H-DDNSK4 × 11 × 4rubber seal359
694-H-ZZNSK4 × 11 × 4shielded, both sides290
694U-Hbrand not stated4 × 11 × 4open (no seal or shield)332
694ZZNSK4 × 11 × 4shielded, both sides397
F604ZZNSK4 × 13.5 × 4shielded, both sides424
F624ZZNSK4 × 15 × 5shielded, both sides424
F634ZZNSK4 × 18 × 5shielded, both sides383
F684-H-ZZNSK4 × 9 × 4shielded, both sides422
F684ZZNSK4 × 9 × 4shielded, both sides353
F694-H-ZZNSK4 × 11 × 4shielded, both sides319
F694ZZNSK4 × 11 × 4shielded, both sides411
MF74ZZNSK4 × 8.2 × 2.5shielded, both sides392
MF104ZZNSK4 × 11.6 × 4shielded, both sides335
605-H-DDNSK5 × 14 × 5rubber seal278
605-H-ZZNSK5 × 14 × 5shielded, both sides239
605U-HNSK5 × 14 × 5open (no seal or shield)364
605ZZNSK5 × 14 × 5shielded, both sides341
625-H-DDNSK5 × 16 × 5rubber seal385
625-H-ZZNSK5 × 16 × 5shielded, both sides336
625-H-ZZU76U-01NSK5 × 16 × 5shielded, both sides848
625DDNSK5 × 16 × 5rubber seal329
625DDUNSK5 × 16 × 5rubber seal262
625VVNSK5 × 16 × 5rubber seal313
625ZZNSK5 × 16 × 5shielded, both sides277
635-H-DDNSK5 × 19 × 6rubber seal597
635-H-ZZNSK5 × 19 × 6shielded, both sides418
635U-HNSK5 × 19 × 6open (no seal or shield)435
635VVNSK5 × 19 × 6rubber seal285
635ZZNSK5 × 19 × 6shielded, both sides277