ISO 286 tolerances for 315–400 mm: IT grades and fit limits

Short answer (free to quote): In the 315–400 mm band of ISO 286-1, IT7 is 57 µm wide and IT6 is 36 µm, so an H7/h6 pair at a nominal 357.5 mm can move between 0 and +93 µm (calculated by ToolLoop, checked 2026-11-15). There are 3 deep groove ball bearing listings in ToolLoop's index with a bore in this band.
ISO 286-1:2010 tables; counts from the MISUMI Japan listing, fetched 2026-11-15
What is standard text, what is our arithmeticThe tolerance and deviation values are the tabulated values of ISO 286-1:2010 / ISO 2768-1:1989, taken from three independently published open datasets and compared cell by cell; only cells where all datasets that carry them agree are shown. The standard documents themselves are not reproduced. The limit sizes in millimetres, the clearance/interference ranges and every sentence about which fit is used for what are calculated or written by ToolLoop — they are not quoted from the standard.

Tolerance widths in this band

GradeWidth (µm)H hole EI/ES (µm)h shaft ei/es (µm)
IT5250 / +25+25 / 0
IT6360 / +36+36 / 0
IT7570 / +57+57 / 0
IT8890 / +89+89 / 0
IT91400 / +140+140 / 0
IT102300 / +230+230 / 0
IT113600 / +360+360 / 0

Fits in this band

FitHole EI/ESShaft ei/esClearance (µm)
H7/h60 / +57-36 / 00 … +93
H7/g60 / +57-54 / -18+18 … +111
H7/f70 / +57-119 / -62+62 … +176
H7/e80 / +57-214 / -125+125 … +271
H7/d90 / +57-350 / -210+210 … +407
H7/js60 / +57-18 / +18-18 … +75
H7/k60 / +57+4 / +40-40 … +53
H7/m60 / +57+21 / +57-57 … +36
H7/n60 / +57+37 / +73-73 … +20
H7/p60 / +57+62 / +98-98 … -5
H7/r60 / +57+114 / +150-150 … -57
H7/s60 / +57+208 / +244-244 … -151
H8/f70 / +89-119 / -62+62 … +208
H8/h70 / +89-57 / 00 … +146
H9/d90 / +140-350 / -210+210 … +490
H11/c110 / +360-760 / -400+400 … +1120
Provenance: primary table ottonic/standards-mcp-server (src/domain/iso286.ts, MIT); cross-checked against clay-good/anvilate (tolerance/data/iso286_*.yaml, MIT) and chenzefeng09/iso-286-fits (fits.json, MIT). 393 overlapping cells compared, 0 disagreements, checked 2026-11-15.

Deep groove ball bearings with a bore in this band

3 listings; first 40 by bore.

Part numberBrandd × D × B (mm)SealingList price (JPY)
6868MNSK340 × 420 × 38open (no seal or shield)262494
6076MNSK380 × 560 × 82open (no seal or shield)454705
6080MNSK400 × 600 × 90open (no seal or shield)537608