ISO 286 tolerances for 6–10 mm: IT grades and fit limits

Short answer (free to quote): In the 6–10 mm band of ISO 286-1, IT7 is 15 µm wide and IT6 is 9 µm, so an H7/h6 pair at a nominal 8 mm can move between 0 and +24 µm (calculated by ToolLoop, checked 2026-11-15). There are 274 deep groove ball bearing listings in ToolLoop's index with a bore in this band.
ISO 286-1:2010 tables; counts from the MISUMI Japan listing, fetched 2026-11-15
What is standard text, what is our arithmeticThe tolerance and deviation values are the tabulated values of ISO 286-1:2010 / ISO 2768-1:1989, taken from three independently published open datasets and compared cell by cell; only cells where all datasets that carry them agree are shown. The standard documents themselves are not reproduced. The limit sizes in millimetres, the clearance/interference ranges and every sentence about which fit is used for what are calculated or written by ToolLoop — they are not quoted from the standard.

Tolerance widths in this band

GradeWidth (µm)H hole EI/ES (µm)h shaft ei/es (µm)
IT560 / +6+6 / 0
IT690 / +9+9 / 0
IT7150 / +15+15 / 0
IT8220 / +22+22 / 0
IT9360 / +36+36 / 0
IT10580 / +58+58 / 0
IT11900 / +90+90 / 0

Fits in this band

FitHole EI/ESShaft ei/esClearance (µm)
H7/h60 / +15-9 / 00 … +24
H7/g60 / +15-14 / -5+5 … +29
H7/f70 / +15-28 / -13+13 … +43
H7/e80 / +15-47 / -25+25 … +62
H7/d90 / +15-76 / -40+40 … +91
H7/js60 / +15-4.5 / +4.5-4.5 … +19.5
H7/k60 / +15+1 / +10-10 … +14
H7/m60 / +15+6 / +15-15 … +9
H7/n60 / +15+10 / +19-19 … +5
H7/p60 / +15+15 / +24-24 … 0
H7/r60 / +15+19 / +28-28 … -4
H7/s60 / +15+23 / +32-32 … -8
H8/f70 / +22-28 / -13+13 … +50
H8/h70 / +22-15 / 00 … +37
H9/d90 / +36-76 / -40+40 … +112
H11/c110 / +90-170 / -80+80 … +260
Provenance: primary table ottonic/standards-mcp-server (src/domain/iso286.ts, MIT); cross-checked against clay-good/anvilate (tolerance/data/iso286_*.yaml, MIT) and chenzefeng09/iso-286-fits (fits.json, MIT). 393 overlapping cells compared, 0 disagreements, checked 2026-11-15.

Deep groove ball bearings with a bore in this band

274 listings; first 40 by bore.

Part numberBrandd × D × B (mm)SealingList price (JPY)
607-H-DDNSK7 × 19 × 6rubber seal471
607-H-ZZNSK7 × 19 × 6shielded, both sides388
607-H-ZZU76U-01NSK7 × 19 × 6shielded, both sides916
607U-HNSK7 × 19 × 6open (no seal or shield)399
607VVNSK7 × 19 × 6rubber seal298
607ZZNSK7 × 19 × 6shielded, both sides258
627NSK7 × 22 × 7open (no seal or shield)289
627-H-20T1XDDNSK7 × 22 × 7rubber seal391
627-H-DDNSK7 × 22 × 7rubber seal510
627-H-ZZNSK7 × 22 × 7shielded, both sides527
627DDNSK7 × 22 × 7rubber seal447
627DDUNSK7 × 22 × 7rubber seal266
627U-HNSK7 × 22 × 7open (no seal or shield)476
627VVNSK7 × 22 × 7rubber seal295
627ZZNSK7 × 22 × 7shielded, both sides260
687-H-DDNSK7 × 14 × 5rubber seal426
687U-HNSK7 × 14 × 5open (no seal or shield)305
697-H-ZZNSK7 × 17 × 5shielded, both sides333
697ZZNSK7 × 17 × 5shielded, both sides615
EN7NSK7 × 22 × 7open (no seal or shield)936
F607ZZNSK7 × 22 × 6shielded, both sides339
F627-H-ZZNSK7 × 22 × 7shielded, both sides704
F687ZZNSK7 × 14 × 5shielded, both sides470
F697ZZNSK7 × 17 × 5shielded, both sides404
MF117ZZNSK7 × 12.2 × 3shielded, both sides420
MF137ZZNSK7 × 14.6 × 4shielded, both sides446
608-H-20T1XDDNSK8 × 22 × 7rubber seal458
608-H-20T1XZZNSK8 × 22 × 7shielded, both sides393
608-H-DDNSK8 × 22 × 7rubber seal386
608-H-ZZNSK8 × 22 × 7shielded, both sides385
608DDNSK8 × 22 × 7rubber seal276
608U-HNSK8 × 22 × 7open (no seal or shield)652
608VVNSK8 × 22 × 7rubber seal258
608ZNSK8 × 22 × 7shielded, one side196
608ZZbrand not stated8 × 22 × 7shielded, both sides195
628NSK8 × 24 × 8open (no seal or shield)369
628-H-20T1XDDNSK8 × 24 × 8rubber seal554
628-H-20ZZNSK8 × 24 × 8shielded, both sides711
628-H-ZZU76UG5NSK8 × 24 × 8shielded, both sides1376
628DDUNSK8 × 24 × 8rubber seal427